How To Put A Pool Cover On An Inground Pool

Download a printable copy here: Pool Cover Installation Guide

INSTALLING THE INGROUND . POOL COVER

Contents

Instructions for installing a safe roof for swimming poolsThe pool safety cover is fixed to the deck via straps, springs and anchors. Brass anchors thread up to install the cover and go under the deck when the cover is removed. Installing your own safety pool cover is an easy do-it-yourself project and only takes a few hours to complete.

LIST OF DOCUMENTS

  • Heavy duty rotary hammer drill, with 3/4” x 18” long masonry drill bit
  • Extension cord for powering hammer drill
  • Chalk line for marking
  • Hammer to shuffle deck anchor
  • 12-24 buckets of water or sandbags to keep the pool cover in place
  • Protective glasses / goggles

WARNING: Always wear goggles or other appropriate eye protection while installing anchors or other pool equipment using power tools.

HARDWARE INCLUDED

Materials to install the swimming pool cover

INSTALLING POOL COVER

1. Remove all ladders and pool handrails 2. Measure the pool wall and pool cover. This will determine the cover overlap. Take the difference in width and length and divide by two. The overlap can vary from 10 to 15 inches. 3. Place the cover over the pool carefully so you don’t jerk or damage the pool cover. The warning label must be facing up. Adjust the overlap determined in step 2. Use something on the straps to hold the lid in place (a bucket of water or a sandbag). 4. Mark anchor points at the center of each wall. They are located 18 inches from the edge of the pool cover. Install the anchors. 5. Attach the strap to the spring, then place the spring in the anchor. 6. Continue with the anchor points for the rest of the pool cover. With all anchors and springs installed, re-check all Anchors and straps to make sure they are securely held and adjusted to equal tension.Instructions for installing a safe roof for swimming pools

ANCHOR Layout

Read more: How to draw a zebra head Once the cover has its initial anchors, lay out the remaining straps (18″ from the edge of the cover). On rectangles, you can use a chalk line to make sure the anchors are in a straight line.

INSTALL ANCHOR

CONCRETE TESTINGInstructions for installing a safe roof for swimming pools

See Also  How To Root Galaxy S8 Sm-g950u
  • Drill about 2-1/4 inch into the deck using a rotary hammer drill with a 3/4 inch masonry bit. Vacuum or drain the concrete dust from the bottom of the pit.
  • Remove anchor insert from anchor. Place the brass anchor in the hole and insert it carefully until the deck is clean using the tamper tool. Do not drive the anchor in with the anchorage set in place.
  • Screw the anchor insert to the anchor with a hex key, with about 1/3 of the anchor insert above the deck to secure the spring.
  • CHECK OTHER SIDES

  • To install Tiles, Pavers, Stone (or laminate floors smaller than 1-5/8″) you will need a 3/4″ ID conduit or 15″ length pipe. Drill into the deck with a hammer drill. Rotate with a properly sized masonry tip.Aspirate or discharge concrete dust from the bottom of the pit.
  • Remove the brass insert from the anchor. Place the copper anchor in the pipe and thread the pipe through the hole and carefully insert it until a block of wood has washed the floor. Do not drive the anchor in with the anchorage set in place.
  • Screw the brass insert to the case with a hex key, with about 1/3 of the anchor insert above the deck to secure the spring.
  • SPRING W-BUCKLE INSTALLATION

    Instructions for installing a safe roof for swimming pools

  • #1 See-through lace strap
  • Go through #2
  • Go between #2 and #3
  • Around the square at the end of spring
  • Back between #2 and #3
  • Push top below #4
  • SPRING W / D-RING INSTALLED ANCHOR

    Spring with D-Ring . Settings

    SPRING SETTINGS ON FACE BY ANCHORS

  • Place the installation rod over the round end of the spring with the groove on the rod facing away from the cap.
  • Place the end of the bar on the anchor insert.
  • Rotate the bar away from the edge of the cover until the spring slides over the anchor insert.
  • Rotate the settings bar until the bar is free.
  • Instructions for installing a safe roof for swimming poolsInstructions for installing a safe roof for swimming pools

    SPRING ADJUSTMENT

  • The spring must be compressed by 50%.
  • After the first installation, check the spring tension again to make sure it is correct, the cap should fit snugly.
  • Loose lids can sag and damage.

    REMOVE COVER

  • Place the installation rod on the spring where it connects to the anchor. Make sure the notch is facing away from the cover.
  • Rotate the bar until the spring rests on top of the bar.
  • Pull the bar towards the cap so that the spring slides up the rod and relieves the tension.
  • Using the supplied Hex Lock rotate the anchor insert until it is flush with the deck.
  • See Also  How To Find Out Who Reported A Picture On Facebook

    Instructions for installing a safe roof for swimming pools

    MAINTAIN ANCHORS

    For smooth operation of anchors, it is a good practice that they are flushed every spring and fall to remove dirt. Brass gaskets can also be lightly sprayed with a silicone or Teflon lubricant to ensure smooth operation. Do not use any oil or grease!

    PRESERVE

    When the lid is removed, it should be cleared of debris, allowed to dry, folded, and placed in its storage bag. Store the cap in a dry place, away from rodents.

    CARE OF YOUR COVER

  • Ensure that the pool water level is never allowed to drop below 18” above the main deck water level. Leaving the water level low will result in coating and/or spring damage during snow accumulation. This type of damage is not covered by the warranty.
  • Do not walk on the cover unless there is an emergency. It should not be jumped up like a trampoline. Walking or jumping on the cover may result in damage not covered by the warranty.
  • Proper chemical treatment is required when closing the pool door in winter. Chemical levels should be checked in the spring, adjusted as needed.
  • Bands for abrasion protection are sewn into the case to protect against normal wear.
  • When necessary, installers can add protective padding to sharp corners or very rough areas of the pool.
  • The lid must be stored in the storage bag when not installed. Any leaves and debris should be cleaned from the pods before storing.
  • Covers must be stored in a rodent-free area.
  • Never swim in a pool with the lid on when it is partially installed.
  • Check the cap periodically to make sure it stays firmly on the pool. Adjust the belt to achieve the proper tension.
  • Do not pull the cover on the deck or on the springs of the lid. Tears caused by mishandling will not be covered by the warranty.
  • See Also  How To Convert A PDF/A File To Regular PDF

    Installing an indoor pool cover Read more: how to recover deleted records on directvWhen you purchase a pool cover from Pool Warehouse, all surrounding pool cover installation hardware is included. All the tools you will need to install the hardware and adjust the pool cover in the future are also included. Hardware includes TruSteel springs and caps, brass anchors and flanges, TruSteel washers, and stainless steel ladder buckles. This allows to prolong the life of your swimming pool roof. Spring ladder lock is made from stainless steel to eliminate rust and corrosion. These springs hold the weight of your indoor pool cover while allowing the pool cover to flex. This result allows your enclosure to be resilient in the harshest weather conditions allowing for years of worry-free operation. The included D-rings are galvanized steel that resists rust and ensures structural integrity. The two-piece anchors are made from extremely strong brass, ensuring they never rust or corrode. These flanges will add a touch of class to your anchor points. Included with your pool cover hardware are the exact sized Allen wrenches needed and a setting bar to allow for the necessary adjustments for anchoring and spring removal.

    Have a few questions?

    If you have any questions regarding the installation of a swimming pool cover around any time, please call us at 1-800-515-1747 or email us, [email protected]At Pool Warehouse, We Know Swimming Pools! Read more: how to prevent birds from landing on my deck

    Last, Wallx.net sent you details about the topic “How To Put A Pool Cover On An Inground Pool❤️️”.Hope with useful information that the article “How To Put A Pool Cover On An Inground Pool” It will help readers to be more interested in “How To Put A Pool Cover On An Inground Pool [ ❤️️❤️️ ]”.

    Posts “How To Put A Pool Cover On An Inground Pool” posted by on 2021-10-27 07:13:11. Thank you for reading the article at wallx.net

    Rate this post
    Back to top button