SMOK MAG P3 Kit/ User Manual

Video How to reset smoke magBoth Morph 219 and the MAG P3 share some of the same features. However, Smok Mag P3 is an upgraded version and has more features than its predecessor.mag p3 kit 1Before using this product for the first time:

  • Install the appropriate lithium battery according to the instructions for the anode and cathode (see below).
  • Connect the power supply to the tank.
  • Make sure that the set wattage is within the recommended wattage range for the coil, coil version and recommended wattage are printed on the front and back of the coil.
  • Touch or to adjust the wattage.

mag p3 kit 1 11. Power on When the device is off, quickly press the Fire Key 5 times in 2 seconds to turn on the device. The display continuously shows “SMOK”. (If you have set a password, you need to enter your password first) Read: how to reset sml 2. Power off Press the Fire key five times until the interface shows “POWER OFF? Yes or no”; select “Yes” to power off.Also, you can touch the screen and select “SETTINGS” -> “GENERAL” -> “Power off” to turn off the device.stop working when one vaping longer than 10 seconds, release and press again to vape); 2) Short press the Fire key 3 times to lock or unlock the vaping function Note: The Fire key lock will lock the simultaneous touch function. To use touch function again, you need to perform slide to unlock to unlock touch function Screen unlock and touch function Unlocked status Read more: how to make skirt out of shirt1) Touch Smok mag p3or0 1 to adjust the current power or temperature value; 2) Press the Fire Key three times to lock the device (move the arrow to the right and the screen can be unlocked.)first4. You can touch “Settings” > “Passcode” to set your own password.

  • Make sure the coil is securely fastened to the injector base.
  • Fill the e-liquid completely into the flask (see below).
  • Do 2-3 blows with power off and without pressing the Fire key.
  • Start vaping.
  • If e-liquid is aspirated through the SMOK product into your mouth, immediately rinse your mouth completely, seek medical help if necessary (see below), then remove the atomizer and clean up the spill first. when rushing back.
See Also  Instant pot portuguese bean soup recipes

mag p3 0MAG P3 2 1Instructions on how to pour e-liquid into this product Before the e-liquid in the SMOK product runs out, add the e-liquid to the barrel/case. This should be done before the e-liquid is exhausted to avoid burning the coil.MAG P3 3 jpgp3Before filling the e-liquid, the user should put some e-liquid on top of the coil to better saturate the e-liquid and avoid heating the coil without e-liquid.1) Usage tank Using the top refill system, you simply hold it with one hand and use the other hand to twist its drip tip. 2) Add the e-liquid through the slot, taking care not to drip into the center air duct. 3) Close the lid carefully and firmly. Then let it sit for a few minutes so that the organic cotton is completely saturated.SMOK p3Before filling or refilling the SMOK tank, please read the instructions below carefully. Please also carefully read the refill instructions provided with the e-liquid you vape. Before filling the e-liquid into the SMOK product: first check that the nozzle on the e-liquid container is securely attached to the e-liquid container and that the nozzle is at least 9mm long. Then check to see if the nozzle is attached to the e-liquid refillable can easily connect to – and plug into – the SMOK tank. Nozzles attached to the e-liquid receptacle should be narrower and smaller in diameter than the opening in the SMOK reservoir Read more: how to charge a ps4 controller without a charger Carefully connect the nozzle well attached to the e-liquid receptacle, into the opening (i.e. fill slot) of the SMOK tank. Ensure that the e-liquid cartridge nozzle is fully inserted into the SMOK container’s filling slot and there is no e-liquid release until the nozzle is fully inserted into the liquid-slot by Do not touch the e-liquid container discharge mechanism (see instructions for e-liquid containers) until the nozzle is fully inserted into the SMOK reservoir. After the nozzle is completely and securely inserted, and thus the docking system is fully connected, drain the e-liquid from the e-liquid refill container (see e-liquid refill box instructions) . The discharge of e-liquid from the e-liquid filling container must be slow, careful and supervised by the user to ensure absolute no overflow. for 15 minutes to avoid the possibility of coil burning. Make sure that the set wattage is within the recommended wattage range for the coil in use. Replace coil head. Unscrew the screw from the base, pull out the old coil and insert the new coil. Inlet air control. Rotate the airflow adjustment system to control the inlet airflow.MAG P3 TANKIf you have any questions about Smok P3, feel free to contact us! Sharing is caring! Read more: how to quickly raise your credit score 40 points

See Also  How To Remove Background Noise From Blue Snowball

Last, Wallx.net sent you details about the topic “SMOK MAG P3 Kit/ User Manual❤️️”.Hope with useful information that the article “SMOK MAG P3 Kit/ User Manual” It will help readers to be more interested in “SMOK MAG P3 Kit/ User Manual [ ❤️️❤️️ ]”.

Posts “SMOK MAG P3 Kit/ User Manual” posted by on 2021-11-11 15:09:44. Thank you for reading the article at wallx.net

Rate this post
Back to top button