How To Replace Primer Bulb On Ryobi Weed Eater

TruthPrimer has passed its infancy? It’s time to face the fix. Whether you’re a legendary landscape enthusiast or a weekend grass hunter, topqa.info provides the parts, processes and information you need so you can fix failures with ease. easy. The priming assembly injects new fuel into the trimmer’s carburetor, making it easier to start the engine. As with any component in a trimmer’s fuel system, the priming bulb will eventually be damaged by frequent contact with fuel. Fortunately, replacing the primer assembly is easy to do. Read: how to replace the bait bulb on a ryobi weed eater This article provides step-by-step instructions for removing and installing the bait and hose assembly on the Ryobi trimmer.Start.OvercomeREMOVED PRIMER [top] 1. Remove the rear cover.Remove the screws (4) from the back cover.Remove the back cover screwsRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Remove the rear cover from the engine.Remove the back coverRead more: how to remove glass from windows Read more: how to remove glass from windows 2. Remove the carburetor.Drain any excess fuel in the fuel tank before servicing the carburetor or fuel lines.Drain fuel before servicingRead more: how to remove the glass from the window Read more: how to remove the glass from the window Remove the screw (2) from the carburetor assembly.Remove the screwsRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Remove the bumper and bumper assembly from the carburetor.Remove the inductor assemblyRead more: how to remove the glass from the window Read more: how to remove the glass from the window Disconnect the throttle wire from the carburetor (this is done with a lifting and twisting motion).Remove the gas lineRead more: how to remove glass from windows Read more: how to remove glass from windows 3. Remove the fuel lines from the primer assembly.Note that the connection inlets/outlets on the back of the primer assembly are of different lengths. It may be helpful to draw a diagram (or take a photo) illustrating the existing configuration before removing the fuel lines.Note the different lengthsRead more: how to remove the glass from the windows Read more: how to remove the glass from the window On the model shown in this article, the fuel return line (between the primer and the fuel tank) attaches to the longer body of the primer assembly. The line between the carburetor and the primer attaches to the shorter body of the primer assembly.Fuel return flowRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Disconnect (2) the fuel line from the back of the primer assembly. These lines can be pulled out of the cluster relatively easily (by hand); however, long nose pliers can be used as needed to remove lines.Disconnect fuel lineRead more: how to remove glass from windows Read more: how to remove glass from windows 4. Remove the primer assembly.The primer assembly is held in place by two locking pins (plastic). Use long-nosed pliers to compress these tabs (which will release the bait assembly from the base).Press tabsRead more: how to remove the glazing from the windows Read more: how to remove the glazing from the window Remove the primer assembly from the mounting base (slide it towards the back of the trimmer; off the trimmer head).Remove the primer assemblyRead more: how to remove glass from windows Read more: how to remove glass from windows INSTALL NEW PRIMER [top] 5. Install the new primer assembly.Align the tab on the new primer assembly (below the short inlet) with the groove on the mounting base.Align tabs with tracksRead more: how to remove the glazing from windows Read more: how to remove the glazing from windows Press / snap the new primer assembly onto the mounting base.Stick the primer in placeRead more: how to remove glass from windows Read more: how to remove glass from windows FUEL LINE SETTINGS [top] 6. Install the fuel lines.The primer kit comes with a new piece of fuel line. To remove the old fuel line, pull the line (previously disconnected) through the carburetor mounting plate (towards the carburetor).Pull the fuel lines overRead more: how to remove the glass from the window Read more: how to remove the glass from the window Disconnect the old fuel line from the carburetor. This line will pull out of the carburetor relatively easily (by hand); however, long nose pliers can be used as needed to remove the line.Remove the fuel lineRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Install a new fuel line in the carburetor.Fuel line installationRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Read more: How to get food out from under the crown Thread the new fuel line through the hole in the carburetor assembly.Break through the opening lineRead more: how to remove the glass from the window Read more: how to remove the glass from the window Connect the new fuel line to the primer assembly (the line from the carburetor attaches to the SHORT inlet on the primer pipe).Fuel line connectionRead more: how to remove the glass from the window Read more: how to remove the glass from the window Connect the fuel return line to the primer assembly (the fuel return line attaches to the LONG inlet on the primer).Connect the way backRead more: how to remove glass from windows Read more: how to remove glass from windows UNIT CLASSIFICATION [top] 7. Reinstall the carburetor.Install the carburetor gasket (if necessary).Install gasketRead more: how to remove the glass from the window Read more: how to remove the glass from the window Insert the throttle cable into the carburetor throttle link.Gas wire connectionRead more: how to remove the glass from the window Read more: how to remove the glass from the window Install the carburetor mounting screws to the bumper and lever.Install the screwsRead more: how to remove the glass from the windows Read more: how to remove the glass from the window Secure the carburetor (and bumper) to the engine with screws (2). Note that the lever and corrugated washer must be properly aligned before tightening the upper screw.Hold the carburetor tightlyRead more: how to remove glass from windows Read more: how to remove glass from windows 8. Replace the back cover.Reattach the rear cover to the engine.Install the back coverRead more: how to remove the glass from the window Read more: how to remove the glass from the window Secure the back cover with screws (4).Hold the back cover tightlyThe endYou don’t have to use your savings to level your lawns. As you just learned, repairing your own device is easy as you follow our step-by-step instructions. You not only restore the function of the trimmer for a fraction of the replacement cost; You already take advantage of future repairs, wherever you can find them. Find your next fix here. [top]Read more: how to become a time agent

See Also  How To Keep Wood From Cracking

Last, Wallx.net sent you details about the topic “How To Replace Primer Bulb On Ryobi Weed Eater❤️️”.Hope with useful information that the article “How To Replace Primer Bulb On Ryobi Weed Eater” It will help readers to be more interested in “How To Replace Primer Bulb On Ryobi Weed Eater [ ❤️️❤️️ ]”.

Posts “How To Replace Primer Bulb On Ryobi Weed Eater” posted by on 2021-10-26 23:11:09. Thank you for reading the article at wallx.net

Rate this post
Back to top button