How To Install Above Ground Pool Liner With Deep End

Video How to install above ground pool liner with deep endDoughboy® Pools has a long and rich history in the US. They are one of the only above-ground pools with a deep end. They are also the only above ground pool to use an Expandable pool pad. Expandable pool pads stretch into shape as you fill the pool, by slowly releasing the vinyl liner as the pool fills with water. Other underlayments are fully lined with walls and floors before filling begins.Doughboy® sell their own expandable pool pads, or you can purchase replacement expandable pads made by GLI, Swimline, or Lomart. , with prices ranging from $159 to $429, depending on size, depth, and pattern.

Do you have a Doughboy® Pool?

• Straight wall sections have a slight curve in the panel.
• The 2-3′ safety ledge is installed around the 5-6′ deep area.
• The deep area is a round bowl, with no bottom of the funnel.

How to install the Expandable Pool Liner

Tools: Set of 18-24 rubber head clamps, soft push brush, round head trowel, screwdriver set, good quality razor.Material: Expandable pool liners made to order to fit the size and depth of the pool interior, new pads and pads and back pads.

STEP ONE: DRAIN POOL WATER, CLEAR LINER

Most Doughboy® pools do not have a main drain, so complete drainage will require the use of a pump, either alongside the pool or a submersible pump. , and using a razor, cut the lining around the base of the wall, all around the pool. The two pulled up the pad to drain the last drops of water into the pump. Remove the pump and remove the liner from the floor of the pool Read more: how to make a led mirror Work around the pool, removing sections of the top rail and coping strips to remove the liner as it passes wall. Replace the top rail segments, but do not replace the counter-strike strips.

STEP TWO: PREPARATION OF WALLS & FLOORS

Now that you can see the wall, take a broom to remove any dust or residue. If rust is visible, scrape it off and repaint it, and consider using wall foam. Also decide if you can reuse the wall groove, between the wall and the floor, or if you should replace it with a pool. The next step is to prepare the floor with a broom and trowel to smooth the sand, reshape areas or add masonry sand if necessary. . Remove any wind-blown gravel or debris, and use the tools to lower the highs and fill in the lows. Start at the deep end and work out the shallow end, creating sharp transitions on the safety ledge and shallow ramp.

STEP THREE: INSTALL LINER

This is where things get different – up until this point, it’s been like any other pool liner job, but for the expandable liner, the next step is unique. traffic junctions with duct tape. This will be helpful to make sure the liner doesn’t ‘skew’ from the circular or oval pool shape. With 4 people, carry the pad and place it on top of the shallow end rail. Using tongs and all four, carefully pull the pad across the pool, pull it over the top rails and gently clip it to the rails. Loosen the pool liner, so that the seam between the wall and the floor is 4-6 inches from the top of the pool wall, then re-wrap the pad to the top rail around the pool.

STEP FOURTH: COMPLETE THE POOL, GET OUT

The final step to installing the expandable liner is the one that needs attention. Start filling the pool with water and let the liner become taught and stretched. Read more: how to fix jbl charge 3 squeaking For 1/10th of the water added, release the liner 1/10th of the way. This is done gradually, releasing some clamps, allowing the liner to slide a few inches into the pool and fitting the pad onto the top rail. If wrinkles appear, reach over the wall and pull the liner towards topqa.info by truck, although expensive, this step will only take 1-2 hours. If filling from a hose, you will need to let the liner come out a few inches, every few hours until completely filled, which can take 24-48 hours. inches of lining remaining on the outside of the walls. Remove the top rail sections, place the reference strips on top of the liner to secure it to the wall, and trim away excess vinyl material on the outside of the wall. out vinyl inside the visor, to flood the filtration system and plumbing. ~ Congratulations! You have just installed your own expandable pool liner. There may be a few wrinkles, which is normal with this style of pool, but if you are patient and let the lining stretch, wrinkles will be minimized.BONUS TIP:

• Not using an expandable liner on a pool doesn’t mean using a liner – walls can collapse inward during the filling process!
• If filling from a hose, measure your GPM flow rate by filling a 5-gallon bucket, so you can time when to refill the liner.

Balance the water in the pool and start filtering and cleaning and you’re ready for your first swim in your newly lined Doughboy® pool! Davy Merino InTheSwim Blog EditorRead more: How to make a keyhole slot without a router

Last, Wallx.net sent you details about the topic “How To Install Above Ground Pool Liner With Deep End❤️️”.Hope with useful information that the article “How To Install Above Ground Pool Liner With Deep End” It will help readers to be more interested in “How To Install Above Ground Pool Liner With Deep End [ ❤️️❤️️ ]”.

Posts “How To Install Above Ground Pool Liner With Deep End” posted by on 2021-11-09 10:47:31. Thank you for reading the article at wallx.net