Wire Ear Cuff With Changeable Dangles (Tutorial)
69 Wired ear cuffs with interchangeable straps (Instructions)by Rena Klingenberg. © 2003-Current Rena Klingenberg. Registered Copyright These interchangeable ear cuffs would be fun to sell (or give as gifts) with a variety of hanging straps to wear.
You can wear an ear cuff over one ear – or form a pair to wear at the same time.
This style is a nice alternative for those who don’t wear earrings.
Or for those who like to wear more ornaments for their ears in addition to their earrings!
Power supply for One Ear Cuff:
Contents
- 1 piece of 20 gauge round soft wire, 4 ″ (10.2cm) long. I used Art Wire/Craft Wire.
- Ruler – to measure where to mark your wire.
- Regular black Sharpie marker (or other all-purpose marker) – for marking your strings.
- Sharpie markers have an extra-small tip – for use as a mandrel.
- Wire cutter.
- Wire rounder/cup pin, jewelry file, whetstone, or emery board – to smooth and round your wire ends.
- Nose pliers ring.
- Supplies to hang on your ear cuffs – necklaces, charms, necklaces, beads, head clips, etc
Note about these ear cuffs:
While many ear cuffs are made to wear each other in both ears, this particular ear cuff design is made to fit specifically to the right or left ear:
The long side of the ear cuff wraps around the back of your earlobe; the short part of the earlobe that wraps around the cartilage inside your ear:
Both the left and right ear cuffs are made exactly the same – until you bend them around your Sharpie mandrel.
How to wear an earring:
The simplest way is to wear the ear cuff around the top of the ear, then slide it down to the area you want to wear:
The short side of the cuff should wrap around the cartilage inside your ear, and the long side of the cuff should wrap around the back of your ear. .
How to make a wire ear cuff with an interchangeable strap:
Cut your 4-inch (10.2cm) piece of string Read more: how to make a resume for modeling We will now round and smooth both ends of this rope, using a wire rounder. /cup pin (or jewelry file, whetstone, or emery board):
Next, we’ll make two marks on our wire so we know exactly where to bend it. Place your string on your ruler and use your Sharpie to make these two marks on your string (the blue lines represent where you will make your points): 
Now we will bend the wire according to the two marks we just made. Step-by-step instructions are below this photo: 
- Photo 1: Use the tips of the round nose pliers to grasp your wire, just above the 0.75 ″ mark you made on the wire.
- Photo 2: Now bend both ends of the wire straight down.
- Photo 3: Now use the tips of the round nose pliers to grasp your wire, right above the 1.25 ″ mark you made on the wire.
- Photo 4: Straighten both sides of the wire down.
Now your wire should look like this:
It’s time to make a small loop at the top of the ear cuff. Use the tips of your round-nose pliers to grab the ends of your short wire ends:
. . . and wind that end of wire into a small loop:
Your wire should look like this:
Now we will create an open wire spiral with a long straight end. (If you’re new to creating open wire spirals, check out my quick video, How to make an open wire spiral.) Use the tips of your round-nose pliers to grasp the end of your long wire: 
Now we will bend the wire into an open spiral. Step-by-step instructions are below this photo: Read more: how to post lost and found on craigslist
- Photo 1: Wind the end of the rope into a small hook (which will eventually become the center of the open spiral).
- Photo 2: To develop an open spiral, continue to move your pliers slightly along your straight wire, creating a small curve in the wire each time you move the pliers.
- Photo 3: Continue moving the pliers along your straight wire in small increments, creating curves in each step, until you have created an open spiral directly opposite the small loop of wire you created at the other end of the wire. .
- Photo 4: Now your wire should look like this.
Use your round-nose pliers to tweak your wire a bit, to make the small circle and spiral open, each round hitting the straight wire that runs across the middle of your ear cuffs:
Your wire should look like the image below. Look at the “wings” protruding on each side of your ear cuffs. You will see a short wing and a long wing:
Now it’s time to bend the wire around our mandrel (our fine point Sharpie marker).This step is where we choose to make the ear cuff fit either the left or right ear (as shown in the image below).If you put the wire across the Sharpie with the short wing on the left, you will create an ear cuff to wear on the left ear, and if you thread the wire through the Sharpie with the short wing on the right, you will create an ear cuff to wear on right ear:
After you’ve chosen your left or right ear, it’s time to bend your cord around the Sharpie mandrel.
- Photo 1: Place your thumb on the top of your string. Your thumb should cover the small circle and open spiral.
- Photo 2: With the fingers of your other hand, bend the “wing” of the ear cuff as much as you can around the Sharpie mandrel.
- Photo 3: Now remove your wire from the Sharpie and use your round nose pliers to give more curves to the tips of your ear cuffs.
- Photo 4: Now your ear band is complete.
How to Attach Dangles to Your Ears
You can wear the ear bands without decorations or add interchangeable hangers like charms, rings, necklaces, beads on the head clip, etc. Simply thread them into the open spiral at the bottom. of the ear band like this:
Read more: how to stop rolling your eyes
Last, Wallx.net sent you details about the topic “Wire Ear Cuff With Changeable Dangles (Tutorial)❤️️”.Hope with useful information that the article “Wire Ear Cuff With Changeable Dangles (Tutorial)” It will help readers to be more interested in “Wire Ear Cuff With Changeable Dangles (Tutorial) [ ❤️️❤️️ ]”.
Posts “Wire Ear Cuff With Changeable Dangles (Tutorial)” posted by on 2021-09-04 05:39:51. Thank you for reading the article at wallx.net
