how to wire a capacitor to two amps

Read more: how to use a keg thumper Read more: How to hang a mezuzahRead: how to wire a capacitor to two amps Question and answerRead more: how to use a keger keg Read more: How to hang a mezuzahRead: how to wire a two amp capacitorWe there are four questions mainly related to capacitors and multi amp systems (two topics).Q1: “Is there any trick to wire TWO amps into a capacitor” Read more: how to use a keg thumperRead more: How to hang a mezuzahRead: how to wire a capacitor to two ampsA1: No, there aren’t any tips for wiring two amps into one capacitor. Here’s how you connect it all.

Run a power cord, large enough to carry the effective load of both amplifiers, to your amp rack. Connect this as close to the battery as possible with a fuse capable of carrying the current required by both amplifiers (add the amplifier fuse values together to get the total required fuse size). ). This fuse is to protect the main power cord (and your vehicle in the event of a live short).

Connect the other end of this mains lead to the positive terminal of the capacitor. Connect the negative terminal of the capacitor to ground. NOTE: Capacitors should be mounted as close to your amplifier as possible.

Connect the positive terminal of each amplifier to the positive terminal of the capacitor.

Q2: “I was reading your post (on how to install a capacitor) and some others and instead of using a resistor I was told the test light should work.” Read more: how to use a keg thumper Read more: How to hang a mezuzahRead: how to connect a capacitor to two ampsA2: The test light will also work because of its internal resistance. Any way is fine. If using the test light to charge the capacitor, follow these steps.

Connect the negative terminal of the capacitor to ground

Connect the test lamp between the positive terminal of the capacitor and +12 volts

When the test light is off, the capacitor is charged

Q3: “I was wondering if you could tell me exactly what wire I run my remote from the amp to the factory radio on. I used to be in power and just wanted an expert to better understand the matter. ”Read more: how to use keg thumperRead more: How to hang mezuzahRead: how to wire a capacitor to two ampsA3: Your factory radio may not have a remote control cord as most factory radios have a built-in amplifier and no remote control cord is required. It may have a power antenna cord but it will only work when the radio is on and not the CD/tape. The poor man’s method is to wire the remote terminal from a switched +12 volt source. Connect the wire to the +12 volt igniter or wire to the switch. Wiring it to the +12 volt igniter will turn on the amplifier every time the car is running, even when the radio is off. You can wire in a simple switch that allows you to turn the amp on or off through that switch. It will only be connected to constant voltage or +12 volt ignition and will have the ability to turn off if desired. There are also units that will sense voltage on the factory speaker wire and then send a +12 volt signal to the remote wire. two ampsQ4: “I am installing two amps in my ford ranger. Would it be easier to run two separate power cables, or is it better to run one large cable then go to a distribution block then to the amps? Also, for ground, should they both be grounded to the same place or to two different bolts? I have read on different websites that two points are the best and others say the same point is the best. ”Read more: how to use keg thumperRead more: How to hang mezuzah Read more: how to wire a capacitor to two amps of sponge in minecraft | Top Q&AA4: I would run a single wire in a multi-amplifier wiring situation for some reason.

See Also Best creole food new orleans

It’s usually cheaper than two wires

It’s easier to run a wire

You only have to make one connection at the pin

You only need a fuse holder near the battery

I use regular distributed block, not merge type. They are cheaper and do not require additional fuses as there is already a fuse holder near the battery to protect the mains cord (you will have to install this fuse holder). Some amplifiers do not have an internal fuse (rare) and these will benefit from a fused distribution block. Read more: how to use a keg thumper Read more: How to hang a mezuzah Read: how to wire a capacitor with two base point amps and I think others should too. I could go into all the scientific reasons for this but it all comes down to noise. By no means is either a surefire way to eliminate noise but it does help if the ground points are at least six inches apart or so. That’s my experience but your mileage may vary. Whatever works, works. The Car Audio Help DVD catalog includes five different videos covering a variety of areas of car audio installation and manufacturing. Topics range from basic system installation (head unit, amplifier, speakers, etc.) and mobile security (car alarms and remote start) to subwoofer box design and fabrication. glass fiber. If you are interested in custom fabrication and car audio installation be sure to check out what we have to offer. Click here for discounted DVD packages Read more: how to use a keg thumper Read more: How to hang a mezuzah Read: how to wire a capacitor to two ampsBack to Newsletter Archive Index Read more: how to use a keg thumper Read more: How to hang a mezuzah Read more: how to wire a capacitor with two amps