how to use router as wireless adapter
If you have an old router lying around and you don’t know what to do with it, one option is to turn it into a powerful wireless adapter or wireless bridge, for your PC, home entertainment center, etc. your home or anything else that requires physical involvement. This is beneficial because routers tend to come with more powerful antennas that provide greater signal strength than your average Wi-Fi adapter, and it’s a great way to recharge. old hardware.
Preparation: Installing DD-WRT
For a router to act as a wireless bridge, it needs to operate in “client” mode. Unfortunately, most router firmware available won’t give you the option to turn your router into a client. -WRT before you can continue. DD-WRT is a free Linux-based router software that is compatible with a wide range of old and new routers. Once installed, DD-WRT will speed up your router with significantly more features than it comes with, including changing its operating mode. Installation instructions are available via the DD-WRT Wiki here. Warning, keep in mind that flashing a custom firmware like DD-WRT will most likely void your router’s warranty and, if done incorrectly, could damage your router. . Be sure to follow the instructions from DD-WRT carefully. We are not responsible if you damage your router. You have been warned!
Configuration: Set local SSID and IP
Once you have successfully installed DD-WRT to your router, enter the router’s IP in the URL bar of your browser to access its interface (usually 192.168.1.1). On initial setup, it will prompt you to set up a username and password. The default username is “root” and the default password is “admin”. Read more: Julia how to write funcitno to calculate eigenvalues After login, what will the interface look like. Click on the “Wireless” tab and select “Client” from the “Wireless Mode” drop-down menu. Enter the broadcast name (SSID) of the Wi-Fi signal from your main router. This is the wireless network name that appears in the Wi-Fi list when you open the Wi-Fi settings on your PC. Apply it and go to the “Wireless Security” tab. Enter the password and choose the encryption protocol that suits your key. The final step is to set up the local IP and subnet mask. Go to Setup, then Basic Setup. Read more: how to mix hair extensions that don’t match In the Local IP section, change the default IP (usually 192.168.1.1) to something unique like 192.168.5.1. Make sure to keep the 192.168 octets and change only the last two octets. The subnet mask will be generated automatically, if not, go ahead and enter 255.255.0.0. Leave Default Gateway blank unless your router is using a specific IP address. If your network is using 10.10.0.0, 172.16.0.0 or some other network, be sure to adjust the local IP, subnet mask, and port accordingly. When you press apply, the DD-WRT interface will disappear. Now, when you enter the address to access the router you just configured, you will be prompted with the interface for your main router.
Checking and Troubleshooting
If things don’t seem to work right away, be sure to WAIT. Wait a few minutes and see if the changes take effect. If not, follow these troubleshooting steps. Launch Command Prompt on your PC and enter “ipconfig”. The default gateway should have the same IP as the one you entered in the Local IP settings in DD-WRT. If you get a response, then you must have internet access. If not, you can always change the adapter settings by going to Network Adapter Settings->Right Click on Ethernet Connection->Properties->IPV4.If none of that works, loop Repeat the process by holding down the reset button on the back of your old router for 10 seconds. This will clear all settings stored on the NVRAM that may flash. If you flashed the image of the DD-WRT, the reset will restore it to its default values. Read more: How to adjust kalimba
Last, Wallx.net sent you details about the topic “how to use router as wireless adapter❤️️”.Hope with useful information that the article “how to use router as wireless adapter” It will help readers to be more interested in “how to use router as wireless adapter [ ❤️️❤️️ ]”.
Posts “how to use router as wireless adapter” posted by on 2021-10-30 19:33:21. Thank you for reading the article at wallx.net
