How To Sharpen A Pencil Sharpener

Video How to sharpen a pencilThis is a problem I’ve had since elementary school – my pencil sharpener is dull. Back then, that was a problem. Today, that is an inconvenience. Well, say no more because I’ve learned how to sharpen a pencil sharpener. And it’s pretty easy, with the right tools and enough patience.

How to sharpen a dull pencil sharpener

1. Setting Up the Right WorkplaceSetting up a proper workplace may not seem important, but for me, it is. A suitable workplace is a flat, stable surface. If the surface is not flat or stable, the sharpener may wobble a lot. The blade can cause damage in such a case. Place the sharpener on a flat and solid surface. The blade must point upwards.2. Get a ScrewdriverMost hand-held pencil sharpeners are held together by a screw or screw, depending on the number of blades. The screwdriver should be the right size for the screw on the grinder, usually, the grinder uses small screws. I had to try a few before landing on the right one. Luckily, I have a glasses kit, which comes with a small screwdriver. It perfectly matches the sharpening screwdriver. Some sharpeners use flat head screws. If that is the case, be prepared to get the appropriate screwdriver. If you don’t have a small enough screwdriver, use something small and flat and can fit the screw. Paper clips or a flat end of a fork might work. They are harder to use. Read more: How to say goodbye in Russian3. Remove the screwInsert the screwdriver into the screw and turn it counterclockwise. Continue to rotate until the screw is completely removed. Make sure to track the screw so that assembling the sharpener won’t be a problem.sharpen dull pencil sharpeners4. Remove BladeFlip the sharpener to loosen both the screw and the blade. Don’t try to dig the blade out with your fingers; it can cut you. Here are some things to keep in mind when removing the blades:

  • Turn the grinder upside down to remove the blade.
  • A little shaking may be necessary.
  • Be sure to keep the sharpener close to a flat surface to prevent bouncing when it falls off.
See Also  how to get rid of cellar spiders

5. Repeat steps 1 to 4 if there are more BladesSome grinders have more than one blade. If all of those blades need sharpening, repeat the blade removal process on all of them.6. Use a sharpening stone to sharpen the bladeThis is the difficult part. The blade is very small and very difficult to hold while grinding. But it is not impossible.

  • Wet the whetstone with water. Some whetstones don’t require water, so be sure to follow the instructions from the manufacturer.
  • Others have found that instead of using water, oil is a better grinding wheel lubricant.
  • Place the whetstone on a damp cloth so that it does not move when the grinding process begins.
  • Several types of grinding wheels have different sharpening levels. Grain is a measure of the roughness of a grinding stone. The taller the grain, the less coarse it is. The coarser it is, the more the metal will rub as it passes through. Since the blade is small, I recommend sharpening the stone with a smoother surface. They should have a higher grit.
  • Since the sharpening blade is very small, I recommend using a pair of tweezers or better yet, a needle-nose pliers to hold the blade.
  • Slide the sharp end of the blade through the whetstone at an angle of 20 degrees. A few slides are enough to sharpen the blade.

Read more: How to measure RV Skylight?7. Clean the tongueUsually, all it takes is cleaning the blade for it to work properly. If this is the case, try rubbing a little alcohol on its surface. Even if this is not the case and the grinding is indeed stable, it is a good idea to clean it up afterwards.8. Dry the bladeAfter rubbing with alcohol, dry the blades with a clean cloth. Leaving moisture on a piece of metal is a bad idea. It will be oxidized. The metal will rust and corrode and become essentially useless.9. Reassemble the GrinderNow that the blade is sharp and clean, it’s time to reassemble the sharpener. Use a pair of tweezers to put the blade in its place. Make sure that the sharp edge is on the right side. Screw the screw in place with a screwdriver (turn clockwise). And it’s as good as new!

See Also  How To Make All Periods Smaller In Word

It’s worth it?

To sharpen a pencil sharpener requires several steps. And at first, I wondered if it was worth all the trouble. Honestly, it’s not. Pencil sharpeners are very affordable. I can easily buy a new one when the one I own becomes dull and useless. However, I love knowing that I can sharpen dull sharpening blades. I want to know that, when needed, I can restore the pencil to its original state.

Inference

Pencil sharpeners are convenient tools. But when they get bored, they get frustrated. Thankfully, with the right tools and the right patience, anyone can restore them. Knowing how to sharpen the blades of a pencil sharpener can certainly help. Read more: how to curl hair with a straightener

Last, Wallx.net sent you details about the topic “How To Sharpen A Pencil Sharpener❤️️”.Hope with useful information that the article “How To Sharpen A Pencil Sharpener” It will help readers to be more interested in “How To Sharpen A Pencil Sharpener [ ❤️️❤️️ ]”.

Posts “How To Sharpen A Pencil Sharpener” posted by on 2021-11-08 17:55:45. Thank you for reading the article at wallx.net

Rate this post
Back to top button