How To Set Up Intex Pool Vacuum

Video How to Set Up an Outdoor Swimming Pool Linkage Pool is a cost effective alternative to installing an indoor pool. They come in a variety of shapes and sizes to suit different yards and budgets. They will provide plenty of fun and memorable summer jets as long as you vacuum and maintain like you would with any other pool. to set up and operate. We’ve reviewed this great automatic vacuum cleaner in our article: 11 best aboveground vacuum cleaner reviews of 2018 and if you have, hopefully, read this review, you have Remember that many other vacuums do not work best for Intex pools. Well, this device does it! Read: how to set up an Intex pool vacuum Vacuuming an Intex aboveground pool once a week will help you keep the water looking clean and clear. You also need to maintain the proper chemical balance in your pool water and test it regularly. Intex swimming pool. In some cases, a vacuum cleaner won’t work as well if your pool water is too dirty.

How to connect Intex pool vacuum cleaner

Before assembling the Intex vacuum cleaner, you should be familiar with all its parts. Here are all the parts from the diagram above (1 set each or shown in parentheses):

TOP CLEANER

COLLAR NUT

PEARL MODULE

WOMEN’S NETWORK

SANITIZER FACILITIES

TUBE CLAMPS

HOSE . converter

HOSE A

HOSE B (3 pieces)

HOSE C (3 pieces)

EASY HOSE

SUPPORT BRUSH A (2 PCS) (4 pieces)

BRUSH (10 PCS) (12 pieces)

BRUSH SUPPORT B ​​(2 PCS) (4 pieces)

DISCHARGE RING PLATE

Your automatic vacuum cleaner needs to be connected to a filter pump with a flow rate of 1600 – 3500 gallons/hour. Actual cleaning performance will depend on filter flow rate. The higher the flow rate, the better the performance will be. If your pool has a sand filter, make sure the sand is clean by backwashing it first. Run the filter pump for 10-15 minutes before connecting the automatic vacuum cleaner to the water connector again. Remember that your automatic vacuum cleaner will not work if your filter pump is not working. In case you want to be able to schedule your pump working hours, buy a pool pump timer that will give you exactly that!

How to connect a pool vacuum to an Intex pump

Step 1First, you need to turn off the filter pump. From inside the pool, remove the nozzle from the water return connector (See Figure 1.)Step 2 Now screw the end of tube A (8) with the adapter into the threaded mesh connector, from inside the pool (See Figure 2). Read more: How to use a lawn mower Step 3Connect the rest of the tubes together outside of the tank in one of two possible orders depending on the size of your tank: BBCBCD or BCBD (See Figure 3).Step 4Assemble the brush as shown in Figure 4. (You will need to remove the brush underneath the unit when sucking up large debris or leaves on the pool floor) Step 5With the hose clamp (6), secure the end of hose D (11) to the top connector of the cleaner. No special tools are needed for this: you can use even a small coin to tighten the hose clamp (See Figure 5). Now put your automatic vacuum cleaner in the water. Then, fill the hose assembly with water by submerging the hose into the pool to remove all trapped air in the hose. Step 6The next thing you need to do is hold the automatic cleaner upside down under the water so that the water jet shoots out as shown in Figure 6. This will suck all the air from the faucet and vacuum cleaner and let it sink to the bottom. to clean your pool. Step 7Connect pipe B (9) from the hose assembly to pipe A (8) that you installed in step 2. (See Figure 7). Your automatic vacuum cleaner is now ready to use. Step 8It’s time to turn on the filter pump and make sure the water flowing through the filter is cleaner. The automatic cleaner will now move and vacuum the pool floor. See Figure 8. Read more: How to Use the Peep Sight Rifle: An Effective, Quick and Easy Guide If you notice that the vacuum has started to stir debris and debris from the pool floor, you will need to do so. clean or replace the filter cartridge more often as fine deposits will be trapped in the cartridge. followed our setup guide and the vacuum didn’t even move in the pool, let alone vacuum, the first thing you need to check is that the filter pump is working. Also, lift the automatic cleaner out of the pool to check if water is coming out from either end of the device. The pool has a wrinkled bottom. Simply lift the automatic cleaner off the wrinkled area and smooth the pool floor if you can. If the unit moves slowly, check and clean the filter mesh. Another fix is ​​to clean or replace the filter pump assembly. If you are using a sand filter, make sure that the filter media is clean. If necessary, rinse the filter again. If the filter is still not moving as quickly as you would like, try increasing the flow rate of the filter pump. You may feel like you are swimming, but it is more likely that there is air trapped inside the vacuum cleaner. The water is green, brown or black, check which levels need to be balanced. Another maintenance tip: clean all debris from Auto Cleaner after vacuuming continuously for 2-3 hours.

When the job is done

Make sure the filter pump is turned off and unplug the power cord from the electrical outlet. Clean and dry the device and all accessories and parts thoroughly. The brush should be removed and kept flat and straight during storage. Remember that other vacuums work the same way and have similar setup instructions. If you come across a device that can effectively vacuum Intex like the Auto Cleaner, you are very welcome to let us know and share your experience with us! Continue reading: Intex Pool Maintenance ManualRead more: how to add sashing to a quilt block

Last, Wallx.net sent you details about the topic “How To Set Up Intex Pool Vacuum❤️️”.Hope with useful information that the article “How To Set Up Intex Pool Vacuum” It will help readers to be more interested in “How To Set Up Intex Pool Vacuum [ ❤️️❤️️ ]”.

Posts “How To Set Up Intex Pool Vacuum” posted by on 2021-11-16 11:39:21. Thank you for reading the article at wallx.net