How To Replace Leaf Springs On A Boat Trailer

Is Replacing Trailer Leaf Springs Hard?

So long as you have the proper tools and the right size of leaf spring to replace the old one with it’s not that difficult.The main thing to remember is to always be safe and make sure you have your trailer jacked up safely and you tighten all the nuts and bolts to the proper poundage.Reading: how to replace leaf springs on a boat trailerSee Also: Best Weight Distribution Hitches With Sway ControlWe recently had a leaf spring go out in our travel trailer on a bumpy highway. When we pulled into our campsite we saw that one of the tires had been worn down a lot by the top of the trailer’s wheel well.After further inspection, we realized the leaf spring on the front axle on the passenger side of our travel trailer had completely broken on one end.The leaf spring was completely busted on our travel trailer.We were in a bind and had to call someone to replace the broken leaf spring for us. The repairman recommended that we replace the other 3 leaf springs as soon as possible, or at least replace the one that was on the same side as the new leaf spring.It’s important to always replace leaf springs on a tandem or dual axle trailer in pairs.We ended up having to replace all four because all of them looked worn and almost flat. It just seemed like the safer option to replace them all with leaf springs that were slightly more heavy duty.This is how we replaced our travel trailers’ leaf springs. Keep in mind we are not professionals and any work you do on your RV or trailer is at your own risk.Always be careful when working on your own equipment and be sure to be safe, and only do what you feel is within your wheelhouse of skills.If you don’t feel comfortable working on your own trailer have a professional do it for you.See Also: Best Tire Pressure Monitoring System (TPMS) For RV

We How To Measure For A Replacement Trailer Leaf Spring

The hardest part about replacing leaf springs on any trailer is getting the correct size. There are tons of different kinds out there and you want to get the closest match possible.The first thing you need to know is what the weight rating on your trailer axles is. Most of the time you can find that information on the axle itself.There’s normally a sticker that will tell you the weight rating. If you can’t find it there you may need to get that info from the manufacturer or the trailer’s owner’s manual.Next, look at the leaf springs to figure out what length, how many leaves, and what kind of spring you need.Our travel trailer uses a double eye leaf spring (click to view on Amazon) but there are also slipper springs with a hook end and slipper spring with an open eye end.Most dual or tandem axle trailers use double eye leaf springs and because that’s the kind we know how to replace that’s the kind this article will be about.To measure for a replacement double eye leaf spring you will need to measure from the center of one eye to the other.See Also: Best RV 5th-Wheel & Travel Trailer Tires Review/Buying GuideFor a double eye leaf spring measure from the center of one eye to the other.It’s recommended to remove the old leaf spring and measure it with no load on it but sometimes that’s not always possible.If your leaf springs are old, like ours were they may have flattened out a little bit over time. We were told by the repair guy that there were tons of different sizes of leaf springs and it was really hard to get the correct size so you need to measure carefully.We didn’t have the option to take off the spring first so we measured from eye to eye with the spring on the trailer and tried to find the closest match in the number of leaves, weight rating, and width.The leaf spring on our 32 foot travel trailer was 26 inches from eye to eye when on the trailer. We found that most travel trailer leaf springs with 4 leaves were around 25 1/8 -25 1/4 inches from eye to eye.We figured that the springs had spread about an inch so we went with the 25 1/8 inch leaf spring.We also got springs that were rated for a little more weight than the original ones. Our axles are rated for 4,400 lbs. We choose to get 6,000 lbs leaf springs.They had the same number of leaves and everything fit perfectly. The only difference was a few of the leaves were slightly longer on the new ones.See Also: Best Electric Tongue Jack For Trailers (RV & A-Frame)You can also get new leaf springs with more leaves than the originals you will just have to buy longer U-bolts.If you get larger leaf springs or ones that are rated for more weight than the old ones don’t go too high.Leaf springs are meant to cushion your trailer as it bumps down the road by bending. If you get leaf springs that are too high poundage they won’t move under the weight of your trailer.It will be like having no suspension system at all.It doesn’t matter if your leaf spring is mounted on top of the axle or under it, the process will be almost identical.Each style also uses the same kind of leaf spring, there is no differentiation between under mounted or overmounted ones.Besides the replacement leaf springs and u-bolts you won’t need many tools to replace the leaf springs on a dual axle trailer.

Other Trailer Suspension Parts You Will Need

Read more: How to Transform and Duplicate Objects in Adobe IllustratorOnce you get the proper size of leaf springs you will also need a few more parts to do a proper replacement.You should always replace the U-bolts (click to view on Amazon) whenever you change out any leaf springs.U-bolts should never be reused because they stretch when you tighten them to the proper torque. Also when you undo a U-bolt the nut oftentimes will cross thread on its way out and a reused U-bolt may come loose over time.The U-bolts I linked to may not be the proper size for your trailer’s leaf springs. Make sure you check what kind you will need to go with the size and style of leaf spring you are using.See Also: How To Install An Electric Tongue Jack On A TrailerAnother thing you may want to consider replacing is the shackles and equalizer (click to view on Amazon).The shackles on a trailer suspension system are usually the first thing to wear out. You can replace the shackles and keep the old equalizer if you want to, but sometimes it’s better to just replace both.If you have the time and resources replacing the equalizer and shackles along with the leaf springs on your tandem axle trailer is a good idea.Note the shackle/equalizer kit for a tandem axle trailer I linked to may not be the exact one needed for your specific trailer.You need to make sure the equalizer matches the leaf springs or the axle’s weight rating.

Tools You Will Need

Some of the basic tools you absolutely need are:

• A torque wrench that can do up to 150 ft-lbs (click to view on Amazon)
• Sockets in a number of sizes, you may need the thin wall/deep style to remove your trailers tire depending on the style (click to view on Amazon)
• A breaker bar to loosen stubborn lug nuts and bolts on the leaf springs (click to view on Amazon)
• Rust Penetrant, for rusty nuts and bolts (click to view on Amazon)
• A jack to go under the axle. It doesn’t need to be heavy-duty, just strong enough to lift the axle into place as it will fall once you remove the leaf springs, we used a 2-ton floor jack. (click to view on Amazon)
• Jacks to lift the trailer so you can remove the tire. Make sure you get jacks that are heavy-duty enough to lift your trailer safely. We used two 4 ton jacks. Bottle jacks work great, using two is recommended. (click to view on Amazon)
• Jack Stands, especially if you are only using one jack (click to view on Amazon)
• Hammer, preferably rubber, we really wished we had one when we did our replacement. (click to view on Amazon)

You may also need a grinder (click to view on Amazon) depending on how rusty things are under your trailer. Sometimes you have to cut off the U-bolts just to get the leaf springs off.

How To Replace The Leaf Springs On A Tandem/Dual Axle Trailer

Once you’ve got all the parts and tools you will need you are ready to start replacing the leaf springs.At this point, you may want to spray rust penetrant on all the nuts and bolts you are going to be working on to make them easier to remove.

1. Break The Lug Nuts

Before you do any lifting the first thing you need to do is break the lug nuts on the tires.You need to do this first because if the lug nuts are on super tight or a little rusty you won’t be able to loosen them as easily once the tire is off the ground.You don’t want to take off the lug nuts completely, just get the first turn done so you know they will come off easily later.

2. Jack Up The Trailer

Depending on the size and weight of the trailer this could be an easy or a fairly difficult task.Our travel trailer weighs 9,000 lbs so it took 2 large jacks to get one side off the ground. You want to place the jacks close to the wheels and use the frame to lift on.Place the jack near the tires and use the frame to liftMake sure you are using wheel chocks on the other side of the trailer so it won’t be able to move around.If you are using two jacks be sure you lift the trailer evenly until the tires are off the ground.Once you’ve got the trailer where you want it you can lower the weight of the trailer onto jack stands or set them up for safety.

3. Remove The Tire

You can now remove the first tire.I only take off one at a time because I like the second tire to be in place just in case something happens.

4. Position Jack Under Axle

You can now place the jack under the axle you just removed the tire from.I use a small floor jack but a bottle jack will work as well.Place a floor jack and block of wood or a jack stand under the axle before you start removing the leaf springI also placed a block of wood under as well just in case something happened to the jack.Once the leaf spring is removed the axle will fall if nothing is there to catch it. That’s why you want the axle jack in place before you start removing the leaf springs.

5. Start Loosening Bolts

Now it’s time to start working on all the nuts and bolts that are holding the leaf spring in place.I started by loosening the nuts on the top center of the leaf springs. The ones that are connected to the U-bolts.If the bolts are rusty and just won’t come off you may need to cut them off later.Loosen the U-bolt nuts before removing the shackle bolts that hold up the leaf springs.Next, loosen the bolts holding the two eyes of the leaf spring into place. It’s easier to start with the center bolt which is the one connected to the shackle of the equalizer.These can be a little difficult to remove. If they just won’t budge you can use a torch to heat the bolt which will hopefully loosen it.See Also: Best 5th Wheel Hitches (Reese, B&W, Curt, Andersen, Blue Ox)Once you’ve got the nuts off you may have to hit the bolts with a hammer to get them to come out.If you lift the axle with the jack a little bit this may make it easier for the bolt to come out. It’s a good idea to get a replacement for this bolt as you may damage it when removing it or you may need to cut it off.

6. Remove U-Bolts & Leaf Spring

Read more: how to steep loose tea without an infuserOnce the main bolts holding the leaf spring to the trailer are removed you will notice that the only thing holding up the axle is the jack.Be very careful to not put your hands, feet, or legs under the axle just in case it falls.You can now finish removing the nuts holding the U-bolts. Once you’ve removed the U-bolts and U-bolt plate you can take the leaf spring off.

7. Place New Leaf Spring

Your new leaf spring will have a bolt on the top and bottom in the center.This bolt will align with the leaf spring hanger on either the top or bottom of the axle depending on how your trailer’s suspension system is made. It will also help you center the leaf spring.Use the top or bottom bolt to center the leaf spring on the axle mount.Once the leaf spring is in place you can install your new U-bolts. I reused the U-bolt plate because it was better quality than the new one.You can use the new ones or reuse the old one if it seems better. It’s up to you. The only thing you should not reuse is the old U-bolts and U-bolt nuts.Tighten the U-bolts so they are snug, you do not need to torque them to the correct poundage yet.

8. Insert The Bolt Equalizer Side First

You can now insert the bolt through the eye of the leaf spring on the equalizer side (inside).It’s easier to do the equalizer side first because you may need to adjust the axle position to get the holes to line up with the other side. If you are replacing the shackles you can do this now.See Also: How To Wire Multiple 12V Or 6V Batteries To An RVThe bolt goes through the first shackle, then the leaf spring eye, then the second shackle. The nut will be secured to the bolt on the inside.Insert the first eye bolt through the equalizer side firstYou don’t want to tighten the shackle bolts too snug. The trailer’s suspension system is made to move freely which means the nut should be tightened enough to stay in place but you will be able to move the shackles around.

9. Insert Bolt On Other Eye Of Leaf Spring

Now it’s time to put the bolt on the other side of the leaf spring.If you have the correct length of leaf spring it should be easy to line up the eye with the holes of the leaf spring hanger.You can move the axle jack around or move the axle up or down to line the leaf spring eye upThe reason I used a floor jack for the axle is to make it easier to line up the trailer leaf spring with the mounting hole. A floor jack can move around and it’s easy to jack up or down.Once you’ve lined everything up you can insert the bolt. Make sure the nut is on the inside of the trailer.You can tighten this more than the shackle side but you still want it to be loose enough to allow the leaf spring to move and bend.

10. Remove Axle Jack

Once you have secured the bolts to the leaf spring eyes and have the U-bolts installed around the leaf spring and axle correctly you are now ready to remove the jack holding up the axle.Once you remove the jack the axle will be held up by the leaf spring.

11. Use Torque Wrench To Tighten U-Bolt Nuts

Earlier you secured the nuts on the U-bolts so they were snug. It’s time to torque them to the correct poundage so the U-bolts can stretch securely around the axle and leaf spring but also allow for the proper amount of movement.See Also: The Surprising Differences Between 30A & 50A RVsTo find the correct torque poundage you will have to look up what the U-bolt manufacturer recommends.For my trailer’s U-bolts the recommended torque was 70 ft-lbs.

12. Replace Trailers Tire

Once everything is tightened and secured you are ready to put the tire back on. Remember to tighten the lug nuts in a cross pattern.Tighten the lug nuts as much as possible by hand or with a small wrench. Once the lug nuts are snug you can now lower the trailer slowly and evenly until you are able to remove the jacks.Finish by tightening the lug nuts to the proper torque.

13. Finish Tightening Lug Nuts

Once the tires are on the ground and the jacks are removed you can torque your trailer’s tire to the proper ft-lbs.My 15-inch rims on my travel trailer required 90-110 ft-lbs of torque.

14. Replace The Rest Of The Leaf Springs

You should never replace just one leaf spring, they need to be replaced in pairs or all of them.If you only replace one it may cause uneven wear and improper alignment of your trailer tires.If you are putting on a different size of leaf spring you must replace all 4 so they match.

15. Check Everything After Your First Trip

Once you’ve replaced everything you need to you should do a regular check of all the nuts and bolts.This is especially important during the first miles of travel. It’s also recommended to re-tighten all the lug nuts on the tires after about 50 miles.And that’s how you replace the leaf springs on a tandem or dual axle trailer. The process is basically the same for a single axle trailer you just won’t have an equalizer to deal with.Have any questions about replacing the leaf springs on a tandem or dual axle trailer? Leave a comment below.Read more: How many shots to get drunk

Last, Wallx.net sent you details about the topic “How To Replace Leaf Springs On A Boat Trailer❤️️”.Hope with useful information that the article “How To Replace Leaf Springs On A Boat Trailer” It will help readers to be more interested in “How To Replace Leaf Springs On A Boat Trailer [ ❤️️❤️️ ]”.

Posts “How To Replace Leaf Springs On A Boat Trailer” posted by on 2021-10-21 06:51:11. Thank you for reading the article at wallx.net