How To Remove Parquet Flooring From Concrete

How to remove parquet from different subfloors: Step-by-step instructions and Tools & Accessories List. Despite its durability, laminate flooring fades and wears out over time, so sooner or later it will all have to be replaced. This is not the easiest DIY task, however, you can still make this semi-complicated floor renovation work on your own. There are detailed instructions on how to remove parquet from subfloor. Read: how to remove parquet from concrete

Removing parquet from various subfloor surfaces

Contents

The wood floor removal process depends significantly on the subfloor types. There are two main subfloor materials, plywood and concrete, and two separate guides for each.

How to Remove Plywood Flooring

Removing parquet tiles from plywood is a meticulous job, especially if some strong adhesive is used to fasten the tiles to the subfloor.

Heat gun.
Tile scraper or floor scraper (small and larger).
Pry bar.
Safety glasses, protective gloves.

Read more: How to ask a cross-functional team about the crm . systemStart by wearing goggles and protective gloves. Then find at least a small gap between the wall and the wooden plank. Place the pry bar precisely into the gap, push gently, and then raise the tile as far as it can go. You will find that the tile is stuck to the plywood in places where the adhesive has been applied. Heat the heat gun and aim it at the underside of the brick. Do not place the gun on the tile closer than 3 inches and never touch the adhesive with the tip of the gun. Wait until the adhesive becomes soft. You don’t have to move the gun, as the tip is specially constructed to transfer heat to all sides of it. Once the glue is soft enough, use a tile scraper or appropriately sized floor scraper to lift the tiles and remove them. In case if some tiles or some small pieces of wood from the area are still attached to the subfloor, use the heat gun again and then scrape them. Repeat this process several times until you have removed all sections, including small pieces of wood and stuck tiles, and the floor is clear. if you want to check if the gun is warm enough. After you finish using the gun, unplug it and allow enough time for the gun to cool down before storing it away.

How to remove parquet flooring from concrete

Removing parquet from a concrete floor is quite easy, especially compared to removing plywood. To loosen the tile you have to apply some force and high frequency vibration, you will need:

Pry bar.
Vibrator or electric hammer.
Tile scraper (optionally you can use a garden grinder instead of a scraper).
Dust mask, goggles and protective gloves.

Put on a dust mask, goggles and protective gloves. Find a small gap (ie match) between two tiles. Place the plow exactly into this gap and push it until you reach the concrete. Pry a brick or two and put them away. Take the vibrator, place it in the hole in the parquet and lower the blade so it becomes even with the subfloor. If you use an electric drill, position its chisel in the same way. Turn on the vibrator or electric hammer and move it slowly forward. The vibration will loosen the bricks without damaging the concrete floor. Repeat this process for each section of the old parquet, finally using a tile scraper to remove all of the floor tiles. In case if the tiles can be separated from the subfloor easily, you can use a standard garden grinder to peel them off the concrete.

Tips and advice

Read more: how to make monkey bread in the microwave Don’t skimp on advice regarding wearing goggles, a mask and dust-proof gloves. Safety first! Before you start removing the wood tiles, don’t forget to remove the baseboards as well. To do that, use a pry bar.If you don’t have a heat gun or electric hammer in the household, you can use a pry bar and floor scraper to pry each individual tile and separate them from the subfloor. However, this is not the best way to remove wood floors because it really takes a lot of time and effort, after removing the tile from the floor, you will also have to remove the glue. Use hot water and soap or buy some special chemical solvents to remove glue. Do not use bleach as they can damage the subfloor, especially the concrete. Old wood can be recycled. Do not try to use bricks as firewood. Manufacturers often cover the wood with a special protective sheath, and it is extremely toxic when heated and burned. Read more: How to draw a truck.