How To Make Leather Knife Sheaths

Sometimes you want something close at hand: not in your pocket, but right where you need it. A pocket watch, compass, knife, cell phone, or any other item you don’t want to dig through are all good candidates for a leather case. You might want to make something to hold multiple tools or any specialized tools you might want to keep handy. If you are a part lover and can’t find a case for your spare, just replace it wherever it says knife. . When saturated, the skin can be stretched and molded to fit different objects.

Materials and Tools

• Leather, medium weight (5 to 6 ounces)
• X-Acto . rotary cutter or knife
• Pencil
• Cardboard from the file folder
• Rowel’s wheel
• Fid
• Grover Tool
• Waxed man-made fibers or fibers
• Leather sewing needles
• Water pan
• Spring clip
• Saran wrap
• Ice
• Dish upside down price

How to make a leather cover

Step 1: Draw your pattern

Lay the knife out on your piece of cardboard and trace roughly around the blade and handle that you want to cover with your sheath. The pattern is asymmetrical, as the back of the sheath has an extension, which will eventually be folded down and sewn to form a loop through which your belt will be threaded. Again, this doesn’t have to be perfect, and it’s better to be too big than too small.

Step 2: Cut out and assemble your pattern

Use scissors to cut a rough line to see your shape when the knife is in place.If you’re happy with it, fold the pattern in half along the line that will make the back of the blade part of the sheath and trim the overlap so the pattern is symmetrical. Push the paper against the blade to see where it is in the pattern. You can see in the photo a small crease in the cardboard, showing plenty of space between the edge of the cardboard and the blade.Next, use a bit of masking tape to really give the pattern a three-dimensional shape like your skin. This allows you to make adjustments now while being easier.You can see that I trimmed the pattern evenly and let the handle touch a bit more. Trim a little more and we’ll be ready to cut the actual upholstery. Cut the tape holding your pattern together and flatten it.

Step 3: Trace and cut your skin piece

Read more: How to start unfollowing onlyfans outfits Drag your pattern onto the wrong side of the leather (matte suede part). This is because a) it’s easier and b) it sets up the hoop so that the right side faces forward. I tend to skip the loop part of the pattern and use it just as a guide to trace a length with a ruler to make sure it’s long enough and topqa.info to your skin with a rotary cutter, but don’t cut into the inner corners where the blade part of the case makes contact with the belt loop, as you will cut too much and create unsightly dents. Stop those places and use an X-Acto knife or sharp knife to complete the cut.

Step 4: Start shaping the skin

Wrap whatever you have in plastic food wrap, using plenty of fabric and tape to secure everything beautifully.Assemble your dish towels, items to be wrapped, a pan of hot tap water, and your spring clamp. Place the sheath of the leather in hot water. It will change color and bubble slightly as the water penetrates the skin. Just a few minutes is a lot.Place your leather item on a dish towel and fold the towel over the leather item and press down to dry and squeeze out excess water. Place the knife on the skin and fold it, forming it on the handle as you move. Using the spring clamp, clamp the leather in place and work the leather so that the skin forms naturally around the blade and handle. You can shape the skin with your fingers so that it hugs the handle. Set it aside to dry, but I usually check every 5 minutes for the first half hour to make sure the leather molds the way I want it to.You can work your leatherwork again in a few hours (depending on temperature and humidity) or leave it overnight. When the skin is dry, remove the spring clips and you will be left with only a “husk” crust.

Step 5: Cut the shell and prepare to sew the seam

Using a rotary cutter, cut the shell to size by trimming off the raw edges and following the contour of the blade and handle. You’re cutting through two layers of skin that’s already been water-hardened, so it’s going to take a little extra pressure. Go slow and don’t cut yourself off.Using a leather cutter, cut a shallow groove in the leather following the edge of the sheath seam. You can do this manually or use a built-in guided gouge.Mark your stitches into the groove with the paddle tool. Six holes per inch is fine. If you don’t have a paddle tool, you can do it freely and go slowly and carefully.Read more: how to make 2 percent whole milk Place your wrapper on a plastic cutting board and, using a scraper, make holes in the dents you’ve made with your rowing tool. Use a small mallet and tap your knob lightly. Once you’ve poked all of your holes, lift up the top layer of the cover and do the same on the bottom part, as your hat will also start to have holes in the bottom layer. Make sure they align or your stitching won’t be as fun. If you don’t have earwax, you can use an ice pick or other sharp object. Fids work slightly better because they make a small slit, not a hole.

Step 6: Sew the belt loop into place

It’s now much easier to sew the belt loop before re-sewing the sheath. Fold your waist flap to the front and adjust it to the size you want and cut it to size. It will be fastened just below the top part of the housing. Any deeper and you may have problems with the handle being not firmly in the housing.Using your four-pronged punch, make a row of holes in both the end of the hoop and the top of the sheath as shown. If you don’t have a leather puncher, you can use a stapler or stapler or anything sharp and pointed. Trim excess leather, if any, at the end of the strap. Using your needle and artificial tendon, sew the loop, going in and out until you have three stitches. Tie the thread and cut the tendon near the knot.

Step 7: Sew the seam

Using a needle and rib, start sewing from the bottom of the piece of fabric near the top of the sheath. Sew the face up through the skin and down through the next hole. Here you can use the double-needle technique, but for such short seams, the single-needle technique will also work. The effect is to create a suture that does not come apart, and with the groove in the skin, the thread is protected and lies flat or below the surface of the skin. Tie the knot, then thread the needle in and out of the end holes a few times, finishing by threading the needle through a layer of skin and pulling it tight. Cut the border flat with the seam and it will be hidden. Using your wooden tip, polish the seam of your cover to even stitch and press the stitches down in the sheath.

Step 8: Insert a knife or other object

Insert the knife. It should only fit a little bit – it will loosen a bit over time. Wear it on your belt. Revel in the knowledge you have made into something interesting.

Related Posts

Before after

Last, Wallx.net sent you details about the topic “How To Make Leather Knife Sheaths❤️️”.Hope with useful information that the article “How To Make Leather Knife Sheaths” It will help readers to be more interested in “How To Make Leather Knife Sheaths [ ❤️️❤️️ ]”.

Posts “How To Make Leather Knife Sheaths” posted by on 2021-11-17 06:43:44. Thank you for reading the article at wallx.net