How To Make A Fishing Rod And Reel Case

Video How to make fishing rod and reel boxby Gordon Macdonald •Most anglers take great pride in their fishing gear and want to take care of it to ensure its longevity. Regardless of the cost of the set, it’s essential to get it to and from your fishing spot safely. The last thing you need after driving some distance to your destination is to get your fishing rod out of the car and find that you have a misaligned guide socket or even worse, a broken drum. There are many rod tubes available that will protect your rod, however most will require you to remove the coil. So being able to transport a pre-assembled rod will help maximize your fishing time. Sometimes anglers can try several places during their outing, especially when fishing for squid for squid, fishing for squid, fishing in shallows for flatheads or exploring areas with light of the Brisbane River in search of fins. Removing your rod to securely store it in a tube between each position can be quite tiring. Being able to store your fishing rod ready with the lure or the terminal pin still attached will protect your rod and also eliminate the risk of the hook going through the seat of another car or passenger. After trying several options, I came up with a cure tube and coil that was simple to make and cheap to make.first. The tools needed to complete this project are pretty basic: a drill and 4-13mm drill bits, hacksaw, coarse sandpaper, file, marker, screwdriver and wrench to match. with M4 screw and nut. If you don’t have a drill and drill bit, a pair of drill bits will certainly do a decent but still rudimentary job. The tools are so simple that this project can even be done by young anglers, with adult supervision.2.Materials required are one length of PVC pipe (50mm in this case), two end caps and a properly sized PVC connector. All of these can be purchased at a hardware or plumbing supply store. PVC pipes can usually be purchased in either 1m length (only suitable for 2 slats 1.95m or less) or 3m lengths, this will allow you to make as little as two pipes for up to 2 rods. ,4m. You’ll also need a bungee strap, buttons, and two screws, which can be purchased at a cutlery store. I used M4 (5/32”) 316 stainless bolts with M4 Nyloc nuts, they were just long enough to catch the nut after attaching the button and bungee ring to the pipe.3.Read more: DominoesThe size of the PVC pipe will be dictated by the size of the lowest guide (strippers) on your rod. Obviously the tube must be wider than the guide for the rod to slide in. For this rod I used 50mm PVC pipe, you may need to use 65, 80 or 100mm pipe. The 3m length of 50mm PVC costs about $18 but I was able to make two tubes with this one. The terminal caps, connectors, and other bits needed to form the two complete tubes brought the total cost to about $40, $20 each.4.This rod has a total length of 7ft (2.12m), or about 1.1m long when detached. I made my pipe about 1.2m long so that I can use it for other rods that may have a different length than this one. Food wrap can be used to hold the two parts of the bar together. Place your rod next to the pipe and mark the overall length you want the pipe to be. This will be the first cut.5.Position the connector next to the rod so that its bottom edge is level with the base of the spindle (body). Mark the spot on your PVC pipe that coincides with the middle of this connector. This will be the second cut.6.Cut the entire pipe with your hacksaw at these two points. Use sandpaper to smooth and slightly taper the lip of the PVC where you cut the tube.7.Place the connector on the shorter PVC section (which will wrap the end of the rod) and mark on the pipe where the end of the connector will be. About 10mm below this line, drill a hole with your smallest drill bit. Expand the hole further using the next sized drill bit.Read more: Tricks on how to hit a vein every time8.Remove the connector and use your largest drill bit (13mm in this case) to widen the hole even further. This hole should be slightly wider than the base of the reel ╨ you may need to use a file to widen it if you don’t have a large enough drill bit.9.Use a hacksaw or cutter to cut a groove from the edge of the PVC pipe down each side of the bore. Check to make sure it is large enough to accommodate the roll pin as shown. Use a file and sandpaper to smooth the edges of the slot.ten.Place the end caps of both pipe and connector segments onto the longer segment. Emphasize these positions. Use some PVC pipe glue to secure them if you want. Position the strap and bungy button as shown in the illustration so that the bungy button will stretch slightly to secure the button. Drill two holes where they will be glued with your 4mm bit. I like to place the pin on the side of the tube at 90º above the roll foot slot so that the small nuts inside won’t rub against the drum bar.11.Secure the button and button in place with your M4 screw and Nyloc nut. Make sure the screws don’t protrude from the nut or they can scratch your rod as you put it in and out. If they are too long, use shorter ones or remove, cut to length and reassemble. Your rod can be inserted into the tube (even with a lure) before the back is slid in with the reel body positioned in the groove. As you slide the ends of the spool up onto your rod, make sure that the line has a little slack as it needs to turn against the body of the reel.twelfth.Once the two sections are slotted together and the bungy section is cut through the button, you can add a quality reel bag to further protect your coils. This particular one will go around the rod tube and fasten. The neoprene flap also includes bungies and buttons. You can paint the tube if you want or attach a few stickers. Once you’ve reached your destination, simply take the rod out of the tube, join the two segments together and you’re ready to fish. This tube is not only convenient but more importantly, it will protect your pre-implanted implants from the risks of transportation.

Last, Wallx.net sent you details about the topic “How To Make A Fishing Rod And Reel Case❤️️”.Hope with useful information that the article “How To Make A Fishing Rod And Reel Case” It will help readers to be more interested in “How To Make A Fishing Rod And Reel Case [ ❤️️❤️️ ]”.

Posts “How To Make A Fishing Rod And Reel Case” posted by on 2021-11-14 06:01:25. Thank you for reading the article at wallx.net