How To Make A Drawstring Bag With A Round Bottom
Learn how to make a round bottom drawstring bag that can stand on its own with this free pattern and tutorial. You can use it for anything, reusable, spacious and beautiful. This easy sewing project takes about half an hour to make and is beginner-friendly. I love things that are both practical and cute, and I love the sleek look of this beautiful flat-bottom drawstring bag. Drawstring bag with round bottom What’s better than a drawstring bag with a flat bottom? First, I want to be able to easily see what’s in there. Then add or remove items from it much faster than a two-way drawstring bag.The rounded bottom adds a nice touch to the simple drawstring bag, which sews straight and quickly.
One more detail – the drawstring closure is 1 1/2 inches from the top edge of the bag and is snug so you don’t have to worry about small things falling out.
Contents
How to use cute 3D drawstring bag
This beautiful bag is perfect for gifts, easy travel, or baby toys, jewelry, makeup or candies. You may not want to use this bag to carry heavy items, but it will certainly last longer if you make it from canvas or denim. You only need three relatively small pieces of fabric to make this round bottom drawstring bag, so it’s a scrap-burning project. Read more: It took me about half an hour to make it from scratch, but if you’re a complete beginner, take your eyes off the clock! Just take your time and don’t rush the process will be much faster the second time.
I also included a free sample for the circular bottom in case you don’t have a bowl the same size as mine or a compass to draw a 5 7/8” (15 cm) diameter circle.
Garment supplies – flat bottom drawstring pocket
- Free PDF template for 5 7/8 inch diameter circle
- fabric – cotton, canvas, denim
- ribbon or cord – 2, each about twice the width of the bag, plus 2 inches
- sewing machine
- a needle
- suitable topic
- sewing pins
- sewing gauge
- fabric scissors or rotary cutter
- Iron
Step 1
Cut three pieces of fabric – one circle 5 7/8″ in diameter (see free PDF sample) and two rectangles – each 9 3/8″ wide and 10 inches high.
Step 2
Serge the 10” edges. I used an directional print, so it was easier for me to see the top and bottom of the bag. If you’re sewing with a non-directional fabric, avoid confusion by using a pencil or chalk to mark the 10″ edge.
Step 3
With the right sides together, pin the serrated edges. Use a vertical pin to mark two points on each side of the bag – the first 3 1/2″ and the second 4″ from the top of the bag – and leave this part intact.
This will come in handy a bit later when we make the drawstring cover.
Sew the side seams of the bag with a 3/8” allowable seam and remember to leave that 1/2” gap open at the top of your bag.
Step 4
Pressing open allows the seam and stitches into place around that small hole.
Sewing a spot that allows the seam to stay in place is our best chance of getting rid of it. Otherwise, the safety pin will most likely get stuck in it when trying to thread the wire into the housing.
Step 5
Read more: how to make rain in after effect Pin the fabric circle to the bottom of the bag – double check where that hole is – and sew it with a 1/2″ allowable seam.
Then, finish the seam with leather scissors or tinsel scissors.
TIP: Sewing a curve is not difficult if you consider the curve to be some small straight stitches. It is useful to adjust the stitch length to 2.00 or 2.5 mm so that you can sew more slowly. Every third or fourth seam, you must lift the presser foot and turn the fabric slightly before putting the foot down as you sew. This helps you direct the needle around the curve. If you’ve never sewn around a curve, here’s a handy Youtube tutorial that can help.
Step 6
Serge top edge of the drawstring pocket. Then, flip it over 2 inches, and check the right side of the bag to make sure that the opening is in place.
Now let’s create the drawstring channel. We aim for two stitches parallel to the folded edge, one above and one below the small hole.
The spacing between rows should depend on the thickness of your drawstring. For thin wires, 1/2 inch spacing works well, but for wider cords you may want up to 1 inch.
Step 7
Attach a safety pin to the end of a rope and thread it all the way around. Tie the two ends together into a knot.
Then, thread the remaining piece of string from the opposite side. Having two cords is awesome – that’s what closes the bag when pulled. And your round bottom drawstring bag is ready to be filled with whatever you like!
I love this cute drawstring bag that can stand on its own like a champ! It really makes me want to sew some more.Read more: how to get fallout 4 screws | Top Q&A
Last, Wallx.net sent you details about the topic “How To Make A Drawstring Bag With A Round Bottom❤️️”.Hope with useful information that the article “How To Make A Drawstring Bag With A Round Bottom” It will help readers to be more interested in “How To Make A Drawstring Bag With A Round Bottom [ ❤️️❤️️ ]”.
Posts “How To Make A Drawstring Bag With A Round Bottom” posted by on 2021-10-21 07:37:04. Thank you for reading the article at wallx.net
