How To Lift Boat Off Trailer For Repair
Video How to lift a boat out of a trailer for repairJim Smith asked:How do I go between the bunkers of my trailer to clean and polish the bottom of my boat. I want to apply your VS721 Bottom Coat on the bottom of my boat, but it’s on a trailer and I need to get to the bottom supported by the beds so I can clean it and apply the VS721 Bra. How can I do this without hiring a crane?Answer:For your convenience, I have highlighted the hyperlinks. Click the hyperlink for more information about the selected product. Read more: how to handle speedball screen inkPROCEDURES FOR TEMPORARY BOAT FOR TEMPORARY SELLERS:Read more: how to fix speedball screen inkFIBERGLASS BOAT: When cleaning the bottom of the boat with ALGAE STRIP, GREEN GENIE, WATER LINE CLEARER or BOAT SCRUB and protect the bottom with VS721 It is important to lift the boat out of the bunker or roller so that you can clean and protect the entire bottom of the boat, otherwise you will be left with unsightly patches that can negatively affect your boat’s performance. boat and will lead to poor performance and future damage. parts of the hull.COLD BOAT and RIB: When cleaning your inflatable boat or RIB with FOUL OFF, COLD BOAT CLEANING MACHINE, BOTTOM LINE SPRAY IS NOT INCREDIBLEor CLEANING SPEED and protect the bottom with POLY GUARD and REPELINit is important to lift the boat out of the bunker so you can clean and protect the entire bottom of the boat, otherwise you will be left with unsightly patches that can negatively affect the boat’s performance and will result in poor performance and future damage to those parts of the hull.NECESSARY EQUIPMENT:
Read more: How to fix a negative cash app balance CAUTION: This is a safe process when done properly and carefully. If you don’t feel confident in your ability or equipment to handle heavy weights, don’t lift your boat this way, get professional help.1. Place the boat and trailer on a stable, level surface.
2. Lower the trailer’s blade to the ground to raise the crane.. You may need a friend to help keep the blade down.
3. Block the transom using cinders or wooden blocks. Make sure there is a 2” x 8” x16 ″ wooden plank between the boat and the blocks to avoid damaging the boat. If the blocks and wood do not match between the ground and the boat, you may have to use additional 2” x 8” x16 ″ wood planks to make up the difference. If the bottom of your boat is angled, use the required scrap wood piece between the blocks and the hull.
4. Place a hydraulic bottle jack under the trailer’s blade and raise the front of the trailer. When the jack is stretched as far as possible, you may have to place blocks and boards under the keel (where the front bulkhead is), to support the boat. Then lower the jack and use the wooden boards below the jack to give you more height. Continue to activate the trailer. This procedure may have to be repeated several times to achieve the required height.
5. Continue to raise the front of the trailer until the boat is level or slightly lowered. Place 2”x8”x16″ wooden plank blocks above and below the keel in the front bulkhead to support the boat. Start lowering the jack until the weight of the boat is supported by the three block and plate columns. Make sure the boat is well supported on each pole and stable. Read more: How to get 3 4 cups
6. Lower the bottle jack. Extend the trailer jack to support the blade and remove the bottle jack. The boat should be well supported and stable on all three masts and the trailer decks should be about 6 to 8 inches below the bottom of the boat. This will give you space to clean and polish areas normally supported by bunks. Do not remove the trailer. It will act as a safety device to catch the boat in case it slips off the blocks or if one of the blocks breaks or the ground becomes weak and the blocks sink. Do not continue working on the boat until it is well supported and stable. To reassemble the boat on the trailer, reverse the procedure above. Read more: how to cure speedball screen ink Lifting your boat out of the bunker or roller gives you access to the complete bottom so you can remove the growth with Strips of algae, Green Genie, Waterline Stain Remover or AlgeriaClean and brighten the bottom with Boat scrub or Alumabrite CBX and to protect it against marine growth, zebra mussels and infiltration with VS721It is important to clean and protect the entire bottom. Working around bunkers and rollers will make any sea developments worse and will affect your boat’s performance. Leaving parts of the bottom of the boat unprotected can compromise the integrity of the boat. This procedure has been shown to be safe for boats at depths of 40 ft. sound and wooden blocks and planks and shims in good condition. You may have to modify this process slightly or adjust your boat on a trailer depending on the model of your boat, e.g. pontoon, catamaran or monohull. This procedure is NOT recommended for fixed-keel sailboats. Read more: how to fix speedball screen ink
Last, Wallx.net sent you details about the topic “How To Lift Boat Off Trailer For Repair❤️️”.Hope with useful information that the article “How To Lift Boat Off Trailer For Repair” It will help readers to be more interested in “How To Lift Boat Off Trailer For Repair [ ❤️️❤️️ ]”.
Posts “How To Lift Boat Off Trailer For Repair” posted by on 2021-11-07 14:23:19. Thank you for reading the article at wallx.net
