How To Knit Fair Isle Flat
The biggest advantage of making our own handles is the freedom to choose different colors and combine them in unique combinations. There are many ways to blend colors together, to create different textures and stripes, to prevent coloration and interlacing.But perhaps the most favorite color combination is knitting yarn, especially Fair Isle. This technique is considered higher level because there are quite a few rules we need to follow to make a colored fabric that looks good: Reading: how to knit fair Isle flat1. Manage several yarns at once in the same row or loop. Remember to always pick one strand from below the other and maintain that order throughout the row/loop. Keep the floats in the back of the job long enough to make sure the fabric doesn’t get stuck. Very complicated, right? Well, not if you use a little useful technique I will explain in this postThe general idea is simple – we don’t carry two or more yarns in a row. Instead, we work the same row or ring with each color separately. That means, if we use two colors in a row, we will work the row with color A, then go back to the beginning of the row and work the same row with color B.THIS IS HOW TO DO ITClick here to watch a how-to video. First, let’s see how to use this technique when we work within.first. Transmission on number of seams required for your pattern. For the pattern shown below, I cast 30 sts to make 5 sts 6 repeats of a simple Fair Isle pattern.2. When it’s time add contrast colorAttach it to the main color with a simple knot. Round 1 of color samples. A few helpful suggestions:a) If you want the contrasting color pattern to stand out, always start the round with that color. b) Because most of the color swatches are depicted in the form of a histogram, it is of great help to use a magnetic guide.Click here to see how you can create your own magnetic guide for almost no costNow let’s go back to our sample. Take it a yarn of contrasting color. Knit the stitches that are supposed to be a contrasting color and thread the stitches that are supposed to be made with the primary color. If we were to follow the chart below, we would do the following:[knit 1, slip 1 with yarn in back, knit 3, slip 1]repeat brackets to end.Read more: how to clean your grips without gum In the photo below you see it the main color (yellow) is merely waiting for your turnwhile we knit and thread the stitches using only contrasting colors.Although we worked on this round once and got to the top of the round, We are not done with this round yet. Follow primary color yarn and work the same round one of the swatches again. But this time we knit the missed stitches and missed the contrast colored stitches.That means for the primary color we will do the following:[slip 1 with yarn in back, knit 1, slip 3, knit 1]repeat brackets to end.Now we can confidently say that We have completed the first round of color modeling ????Since we were working with one color at a time, we solved two big problems: a) There is no need to arrange multiple yarns at once. b) The colors are perfectly aligned on top of each other as you can clearly see in the photo below which shows the reverse side of the work.A few notes about the third main problem – stress. Even with this technique, we still have to pay attention to the floating yarns to make sure we leave enough yarn behind the work to avoid wrinkling. Since we only process one thread at a time it is not difficult to do – As you knit, spread the pretty fabric over the right needle after every few stitches.If you work with a small number of stitches (as I did when making this pattern) and use a double pointed needle or magic loop techniquebe careful with Float formed between the needles. As you move from needle to needle, hold the float close to the fabric with your right hand or pull the float slightly to make it larger.Click here to watch this little tip in the video tutorialNow let’s take a look at this technique when we work flatThe main idea remains the same – we work with every row first with a contrast color, then with a primary color.To be able to go back to the top of the row again (and again if you decide to use three or more colors in the same row), use a circular needle or a pair of double pointed needles.first. Transmission on the number of stitches needed for the pattern + 2 more stitches for the selected patterns. It is not necessary to have an extra stitch on each side of the fabric, but they make the sides look better and act as an anchor point when we change the color. 3 repetitions x 6 sts + 2 sts of your choice + I also added one st to make the swatch symmetrical = 21 sts in total.if you look at the chart above, you will see that the odd number of rows is on the right and the even number is on the left side of the graph. That’s the only difference from the chart we used when we were working in the round, and it showed that we needed to read even-numbered rows from left to right. To avoid confusion, I’d like to add an extra stitch or two to make the color model symmetrical.Read more: Zomboid how to make sheet2. When it’s time Introducing contrasting colorsattach it to the main color at the beginning of the knitting row.3. Row 1. With Contrasting yarn, thread the first stitch (this stitch will be used as the selvedge and we will always knit it with the main color). Then knit the stitches shown in the chart in a contrasting color and thread the stitches shown in the primary color. That means in our sample we will [knit 1, slip 1 with yarn in back, knit 3, slip 1]. Machining the holder to the last seam (the remaining stitch) and threading the last seam As you can see in the photo below, the primary color yarn (yellow) is not active while we knit and thread the colored stitches contrast (orange).The current slide all stitches to the other end of the circular or double pointed needle WITHOUT turning your work. We return to the beginning of row 1 of the swatch.With primary color yarn knit the first stitch, then knit the missed stitches and thread the stitches. That means, we will [slip 1 with yarn in back, knit 1, slip 3, knit 1]. Repeat to the last stitch and knit the last stitch.Twist the strands at the end of the rowand do it after you complete each row of the swatch. Now we’re ready to transfer work and glitter to the second row of the swatch.Watch how to work with glitter in this video tutorialCOLOR OF WOMENIn both patterns, we start working the ring/row with a contrasting color to make color textures more vivid. If you want to make it more delicateStart with the primary color. This image shows how choosing a color changes the look and feel of the template.To make texture at the bottom of the pattern, I started working row by row with a contrasting color. Each row of motif at the top of the pattern starts with the main color. the bottom one seems brighter and more prominent.CAREFULThe the only downside of this way to knit stuck colors is we can’t “catch buoys”. Because we were working with one color at a time, there was no way we could twist the strands at the back of the piece to avoid long drift. That means this technique works best for swatches with no more than five stitches work in the same color.Otherwise, it’s an easy way to create stunning splashes of color with minimal effort.Make your clothes colorful ????Read more: how to get stars in pvz gw2 | Top Q&A
Last, Wallx.net sent you details about the topic “How To Knit Fair Isle Flat❤️️”.Hope with useful information that the article “How To Knit Fair Isle Flat” It will help readers to be more interested in “How To Knit Fair Isle Flat [ ❤️️❤️️ ]”.
Posts “How To Knit Fair Isle Flat” posted by on 2021-10-26 07:37:08. Thank you for reading the article at wallx.net