How To Install Sirius Antenna In Car

Sedan & Coupe | Convertible | SUV | Shuttle truckXM Standard Magnetic Mount Antenna:Read: how to install a sirius antenna in a car If you are installing the XM Standard Mounted Magnetic Antenna, the antenna must be placed on the roof of the SUV. The best location would be in the rear center of the roof as shown. If another antenna is already mounted in this location, place the antenna at least 3 inches away from the other antenna.XM SkyDock Magnetic Mount Antenna:If you are installing the XM SkyDock Magnetic Antenna, the antenna must be placed on the roof of the SUV. The best location would be the front center of the roof, just above the windshield as shown. If another antenna is already mounted in this location, place the antenna at least 3 inches away from the other antenna. Finding the Right Place to Mount the Antenna: Do’s and Don’ts.?DO: Mount the antenna on the roof of the SUV, just above the rear window or front windshield. Read more: how to remove beef curtains without surgery?DO: Mount the antenna on the roof where there is a clear view of the sky in all directions. ?DO NOT: For example, do not mount the antenna inside an SUV on the dashboard. ?DO NOT: Do not mount the antenna on any of the front, side or rear pillars of the SUV. ?DO NOT: Do not mount the antenna near the roof rack. Adjust the bracket so that it is further away from the antenna. If the price is not adjustable, refer to the Pickup section for location. ?DO NOT: Do not mount the antenna near other antennas. Mount it at least 3 inches away. Antenna cable routing:Read more: how to remove the smell of blood– From the back of the roof (XM Standard Magnetic Mount Antenna only) – From the front of the roof (XM Standard Magnetic Mount Antenna and and XM SkyDock Magnetic Mounted Antenna) – Common Troubleshooting Tips Sound and signal reception problemsRoof rear antenna cable routing (XM standard magnetic mount antenna only) Here’s how to route the antenna cable from the XM Standard Magnetic Mounted Antenna to your XM Radio in your SUV. See detailed explanation below the main illustration. You can also view detailed illustrations for each key step by clicking the links highlighted in blue in each section.

Plug the antenna cable under the rubber cover of the rear window/door and thread the cable along the rear hatch. Lift the weather out of the hole and insert the cable inside it. Then replace weather stripping. Pull the cable out of the weather stripping and bring it into the cabin under the interior trim. Avoid hinges or gears that could bend or cut the cable.

Route the cable through the main cabin area of the SUV under the interior trim, towards the front of the vehicle. Use a plastic scraper to lift the plastic just enough to thread the cable underneath. Avoid airbag positions above the rear pillars and above the doors. (Airbag locations are marked with the “SRS” logo.) Be careful not to bend or cut the cable.

Take the cable away from the trim near the panel and route it under the rug toward the panel or control panel. Wind up excess cables in a hidden location, such as under carpets, away from the vehicle’s pedals or controls. Secure excess cable with lanyard.

Take the cable end to the XM Radio position. Leave yourself enough cable so you can easily connect it to the antenna connector (sometimes marked ANT, ANT IN or ANTENNA) of XM Radio Station or Bus Station.

Routing antenna cables from the front of the roof (XM Standard Magnetic Mount Antenna and XM SkyDock Magnetic Mount Antenna) Here’s how to route the antenna cable from your Magnetic Mounted Antenna to your XM Radio in your SUV. See detailed explanation below the main illustration. You can also view detailed illustrations for each key step by clicking the links highlighted in blue in each section.

Use a dull plastic scraper, credit card, plastic knife, or similar blunt tool to lift the rubber mold around the windshield and insert the antenna cable underneath the windshield.

Continue to insert the cable under the windshield molded around the windshield to the lowest angle.

At the lowest angle of the windshield, thread the cable out of the windshield mold and into the weather stripping rubber around the door opening. Lift the weather out of the hole and insert the cable inside it. Then replace weather stripping. Run the cable inside of the weather stripping to the bottom of the door opening.

Pull the weatherproof cable that is stripped at the bottom of the door opening and place it under the rug toward the panel. Wind up excess cables in a hidden location, such as under carpets, away from the vehicle’s pedals or controls. Secure excess cable with lanyard.

Bring the end of the cable out near your XM Radio location. Leave yourself enough cable so you can easily connect it to the antenna connector (sometimes marked ANT, ANT IN or ANTENNA) of XM Radio Station or Bus Station.

Troubleshooting tips for common audio and signal reception problems Here are ways to identify and fix some of the common audio reception and signal problems you may encounter:

PROBLEM: XM RADIO DISPLAY “TEST ANTENNA” or “TEST ANTENNA CONNECTION” or “ANTENNA”
Possible cause #1: The antenna is not properly connected to the Radio or the Car Base, or the connection is loose.
Solution: Check the antenna connection to the XM Radio or Vehicle Dock and make sure it has a good, snug fit.
Possible cause #2: If the antenna is properly connected to the XM Radio or the Vehicle Dock, there may be a broken antenna cable or a problem with the antenna.
Solution: Replace the Magnetic Mounted Antenna.
PROBLEM: XM RADIO DISPLAY “BUG IN SIGNAL” or “NO SIGNAL”
The reason may be: The Magnetic Mounted Antenna does not receive satellite signals.
Solution 1: Make sure the vehicle is outdoors with a clear view of the sky.
Solution 2: Make sure that the antenna is mounted outside the vehicle in the optimal position. (Follow the mounting tips described earlier for your vehicle type.)
Solution 3: Move the vehicle out of the obstructed area. For example, if you are parked in an underground garage, you will receive a signal after leaving the garage.
PROBLEM: The sound of XM Radio has static or loss of clarity
Possible cause #1: If you have connected the audio of your XM Radio to your vehicle’s FM radio using an FM transmitter, the FM channel you have selected is most likely being used by the FM radio. This interferes with the sound of the XM Radio.
Solution: You will need to find an available FM channel. An available FM channel is one that is not used by FM radio stations in your area. When you tune in to the FM radio to an available channel, you’ll only hear silence or silence – no talking or music. We recommend one of the following methods to find available FM channels: Select the first FM channel from your list. Turn on your car’s FM radio (if you haven’t already) and tune it to this topqa.info FM on your XM Radio and then set it to transmit on the same FM channel as your car’s FM radio. Refer to your XM Radio User’s Guide for detailed instructions on how to do this.
Possible cause #2: If you have connected XM Radio’s audio directly to your vehicle’s stereo system using the AUX or AUX IN or LINE IN jacks, the Aux In Cable may not be connected properly.
Solution: Make sure that the Aux In Cable is properly connected; one end connects to the AUX or AUX IN or LINE IN jack on your car stereo system and the other end connects to the “AUDIO” or “AUDIO OUT” connector on your XM Radio or Car Base.
Possible cause #3: If you have connected XM Radio’s audio directly to your vehicle’s stereo using the AUX or AUX IN jacks, or LINE IN, you may not have selected the correct input source on your vehicle’s stereo.
Solution: Set your car stereo to play input from an auxiliary input source.