How To Install Pvc Railing On Deck

Install PVC railing for your floor. Photo by Larry Walton, Photo by Bruce W. Smith

Installation of concrete bearing plastic railing system.

Read: How to install pvc deck railing When I first saw the pile of materials in the garage, I thought, “You must be kidding!” But I don’t want to discourage the host, who takes great pride in his internet shopping. I’m glad I was silent for once. In the end, I was both surprised and pleased with the finished product, my first concern with any railing system I build is that it is sturdy, so I was delighted to discover that This system has reinforced aluminum inside the rails to give them strength. The next thing I discovered was that one of the mounting methods suggested by the manufacturer would work perfectly for our application. New hollow plastic posts can cover a metal pipe and then be concreted. Definitely better, better. I want to keep the baluster-to-rail distance equal to the baluster-to-baluster distance, so we’ll have to locate the newest pylon as we go. Another thing that is predefined is the height of the rails. Because newel posts have grooves to receive top and bottom rails, they have a predefined length and height.BeginThis is how we install the PVC rail system: Start with the new panels that will be on the side of the house. When locating the newel post, make sure there is enough room on the deck surface to fit any trim around the bottom of the newel. to provide strength and stiffness. This also helps to disperse the pressure of the anchor points over a wider area on the inside of the new pillar wall. If there isn’t a frame in your post but the house has a plywood panel behind the bulkhead, this will work but will require more fasteners. In some cases, you may need to open up the wall to add padding or choose another rear mounting method to anchor to the deck substructure. indicates the presence of water pipes inside the wall. Avoid these pipes with your lanyard. This prevents the end of the lanyard from getting too deep into the wood, where the screw end can no longer be grasped. We used a 1/2 inch drill with socket to drive large screws and lags in this project, but an impact wrench would also be a good choice. Be sure to use the side handle on the 1/2 inch drill as these situations create a lot of torque, putting your wrists in danger.Planning the HandRail SystemAssemble a piece of rail by inserting the assemblies into the shoe rails. If the fenders do not form right angles to the rails, it may be because the aluminum core has slipped out of the line. Fix this problem by setting one bar to a square before installing too many rails. Measure the distance between the first baluster and newel and match it to the distance between the balusters. Read: how to install pvc balustrade on deck Read: how to install pvc balustrade on deck Match the gap to the nearest baluster as you did on the newel house. Check to make sure there is room for the kickstand around the bottom of the post and that this matches the post installed at the bottom of the part of the house.Read: how to install PVC railing on deckSettingWhen you are satisfied with the newel’s position, trace around the outside of the post then set it aside. Use a straight edge to create a line between the diagonal corners on the latest post border. Where these two lines intersect is the center of the newel post and the location of the hole you will drill for the anchor tube. Make a hole through the deck of the right diameter for the pipe you have chosen as reinforcement for the newel. For this operation we used a 1/2 inch drill bit. Again, you should use side handles because of the torque involved in making large holes. Thread the hose through the hole in the floorboard and make sure it’s a plumb line in all directions before you use the big hammer. in the ground. I like to use a cuff to keep the top of the post waist-high. Ideally, you will have a depth of 3 feet or more into the ground. Don’t worry about damaging the pipe end; it will be hidden inside newel. Mark the point on the pipe that you are driving. If you can’t bury it to that extent, you can cut the pipe with a hacksaw or reciprocating saw so it’s just below the level of the railing. Read more: NBA 2k17 Badge Guide – How to Earn All Badges in NBA 2k17If your deck size is smaller than combined rail sections, you can cut the top rail and bottom rail to length. When you decide where to cut the track, keep in mind that you want the end or corner to be evenly spaced across the longitudinal and transverse lines of the deck. Also, keep in mind that you need to let the rail sections pass through the new pylons, so make sure to leave this amount. You can cut rail sections using a circular saw or cutter equipped with a carbide blade. Make sure the aluminum core is aligned with the baluster openings in the vinyl before cutting. Safety glasses are especially important for this operation, the handrails may need to be knurled at the point where they intersect inside the corners of the newel post. The idea is to maintain the same distance between the rails and then groove the rails as needed. We find that this is not necessary in our case, because the baluster closest to the newel pillar blocks the concrete, and we reasoned that concrete extending into the rail would better link the system to each other and make it more solid.Anchor with concreteAfter you have assembled the entire system, mark both the newel’s position on the floor and the top of the rail at the point where it should be inside the newel post. You’re about to pour concrete into the pillars, which changes things up a bit. You’ll want to know how to get everything back in place quickly before the concrete sets. Locate a section of a drain pipe or other improvised hopper that will allow you to pour concrete into the small hole in the top of the new pipe without losing the landing material on the deck This is one of those rare projects when using concrete mix bags is a good idea. It takes about 40 pounds of concrete to make each new pier. You don’t want to mix too much concrete at once because the posts and rails need to be adjusted as you move. Rotate the newel to a position parallel and/or square to the floor if necessary. Adjust the rails using the marks you made earlier so that the correct amount is inside the newel pillars. All of these adjustments need to be checked and rechecked as you make them. Tapping the face of the new post as you move it into the plumbing will help with the adjustment process as well as minimize air pockets in the concrete. Use hoses and nozzles to clean leftover concrete that will come out of the newel rod and ray-to-baluster connections. Once everything is in place, let the concrete set overnight. Now, test the sturdiness of the rail system and be amazed at how sturdy it is! Install trim pieces around the bottom of the cogwheel. Install the latest post caps. Choose a cool hat and enjoy. Read more: How long does it take to dye your hair?