How To Connect Pool Vacuum To Filter

Pool cleaning machineVacuuming is the only way, unless you have a robotic pool cleaner, to remove not only sediment from the bottom of the pool, but also microscopic algae spores that have not been filtered by the pool’s filtration system. Your pool catches and so hides in your pool water just waiting to blossom into life. However, the process is quite simple. Read: how to connect a pool vacuum to a filter

How often should I vacuum my swimming pool?

Contents

You should aim to vacuum your swimming pool at least once a week. Skimmers are only capable of removing leaves, dirt and floating debris. Most of the debris entering the pool will float for 3-4 hours, but will then sink to the bottom. )

What equipment do I need?

  • A telescope pole. We strongly recommend this extreme here.
  • A vacuum hose. We recommend this tube here.
  • One vacuum head. There are 2 types: head for concrete or brick lined pool with wheels; brush head for vinyl lined swimming pools. We introduce these Vacuum Heads here.

How to vacuum a swimming pool with a sand filter?

If your pool uses a sand filter, here are the steps.1. Remove large residue or debris. Before you start vacuuming, use a shovel to remove any particularly large leaves or debris that could clog the vacuum head or hose.2. Attach the Vacuum Head to the Telescopic Pole and Tube.3. Flood the hose with water. Submerge the tube and let the water cover. The purpose is to remove trapped air that could be drawn into the pump and create an air mass. Pro tip: hold the hose next to the return outlet to quickly refill the hose with water.4. Attach Hose to Skimmer or Dedicated Suction Port. If your pool has a dedicated suction port, attach a hose to it. If your pool doesn’t have one, vacuum the pool with a skimmer. With most skimmers, you need to remove the basket to attach the hose. The tube port is located at the bottom of the skimmer.5. Vacuuming for the Pool. Using a telescopic pole, move the vacuum head slowly and deliberately across the bottom and walls of the tank.6. Disconnect Hose from Skimmer or Dedicated Suction Port. After disconnecting, you can dismantle the vacuum device.7. Turn off the pump.8. Backwash. Turn the filter valve to the Backwash position. The sand inside the sand filter system blocks debris, dirt and oil. Backwashing reverses the flow of water and pushes dirty water through the drain into the ground or drains. Turn on the pump and backwash for 2 minutes or until the water in the sight glass (which is on top of the filter) comes out clear.9. Turn off the pump.10. Wash off. Turn the filter valve to the Drain position. Turn on the pump and run the wash for 1 minute.11. Turn off the pump.12. Clean the filter. Close the skimmer valve and empty the skimmer filter basket and clean the hair catcher. When you’re done, reopen the skimmer valve. Read more: How to draw a cartoon bell13. Reset the filter valve to filter and turn on the pump.

See Also  Recipes for navy beans vegetarian

How to vacuum a swimming pool with a DE . filter

If your pool uses a diatomaceous earth (DE) filter, here are the steps.1. Continue with steps 1-7, above.8. Backwash. However, the most effective way to backwash the DE filter is as follows:

  • Set the filter valve to Backwash. Turn on the pump and backwash for 2 minutes.
  • Turn off the pump. Set the filter valve to Filter.
  • Turn on the pump and filter for 30 seconds.
  • Turn off the pump. Set the filter valve to Backwash.
  • Turn on the pump and backwash for 90 seconds.
  • Turn off the pump. Set the filter valve to Filter.
  • Turn on the pump and filter for 20 seconds.
  • Turn off the pump. Set the filter valve to Backwash.
  • Turn on the pump and backwash for 60 seconds.
  • Turn off the pump. Set the filter valve to Filter.
  • Turn on the pump.

9. Add DE . powder. Usually this is done through skimmers. Follow the manufacturer’s instructions. We recommend this alternative Diatomaceous Earth (DE) filter media.

How to vacuum a swimming pool with a cartridge filter

If your pool uses a cartridge filter, here are the steps.1. Continue with steps 1-7, above.8. Clean the Toner Cartridge. Turn off the pump, remove the cartridge from the housing and rinse/close the tube. After cleaning, replace the cartridge and turn on the pump again.

How to Vacuum a Pool Without a Filter

If your pool filtration system has a multi-port valve, you can vacuum the pool by going through the entire filter and delivering the vacuumed water directly to the drain. and especially when the water has an algae problem. Live algae easily pass through the filter media and back into the pool. And the same goes for dead algae after shock treatment. A typical multiport system has 6 different settings – Filter, Backwash, Flush, Recirculate, Close and Waste.1. Proceed with steps 1-5, above.6. Turn off the pump.7. Switch Multi-port valve settings to Garbage.8. Turn on the pump.9. Turn off other Skimmer valves. If you have more than one skimmer, turn off the valves at all but the one your vacuum hose is plugged into. Read more: how to put a belt buckle on a regular belt10. Close the main drain valve so that it is half open.11. Vacuuming for Swimming Pool. Move the vacuum head slowly and deliberately over the bottom and walls of the tank.12. Turn off the pump.13. Disconnect Hose from Skimmer or Dedicated Suction Port. After disconnecting, you can dismantle the vacuum device.14. Empty the Pump Basket. Close the skimmer valve to which your hose is attached, then empty the pump basket. When you’re done, reopen all skimmer valves and open the Main Drain again.15. Reset the filter valve to filter and turn on the pump.Note: because vacuuming drains water straight out of the pool, you may need to refill the pool when you’re done. In this case, you need to check and correct the pH and chlorine balance. Click here for instructions on different ways to test your pool water.

See Also  How To Draw A Chocolate Bar

Recommended products

Pool Vacuum HeadVacuum FaucetExtremely Absorbent Pool Suction Pool Water Liquid Tester Pool Water Liquid TesterPool ChlorineSand Sand Replacement Filter Soil Filtration Media High In Soil Fats (DE). Interested in saving your swimming pool cleaning time? You may want to read our article How to Clean a Pool: A Time Saving Guide and Read More: How to Get Sand Out of a Pool Read More: How to Sauna at Home

Last, Wallx.net sent you details about the topic “How To Connect Pool Vacuum To Filter❤️️”.Hope with useful information that the article “How To Connect Pool Vacuum To Filter” It will help readers to be more interested in “How To Connect Pool Vacuum To Filter [ ❤️️❤️️ ]”.

Posts “How To Connect Pool Vacuum To Filter” posted by on 2021-11-05 07:19:12. Thank you for reading the article at wallx.net

Rate this post
Back to top button