How To Clean Smoke Damaged Wood

Read: how to clean smoke damaged wood How to remove soot from wood surfaces Cleaning wood damage can be especially difficult. As a naturally porous material, soot and odors tend to permeate surfaces and often require aggressive cleaning and deodorizing methods. Each type of wood requires specific soot removal products and processes.Finished woodWood is coated with glue or varnish. Most types of wooden furniture (desk, wardrobe, table, cabinet, railing, …) are solid wood. This surface smoke stain remover includes a cleaner that is gently applied to the wood grain where soil is attached for easy removal.Unfinished woodThere are no sealants or varnishes, and it is very susceptible to damage from smoke odors and stains from soot. Unfinished wood typically includes textured wood and the interior of drawers and cabinets. Unfinished wood can also stain easily, so care needs to be taken during cleaning and restoration. bad smell. If the property owner does not want the unfinished wood surface to be sealed (such as wooden cabin walls or exposed wooden beams that detract from the architectural aesthetic), cleaning and degreasing Odors can be particularly difficult. Complete removal of soot and odors is not guaranteed.

Restoration of finished wood damaged by soot

Finished wood is covered with a protective varnish or paint. When involved in a fire or smoke damage situation, damage around the handle is a common pre-existing condition that should be documented.Basic procedure:

Soot’s dry cleaning

If the soot isn’t oily, use a wool vacuum or a HEPA vacuum on all surfaces.

If the soot is almost completely dry, you can use a chemical sponge (dry cleaning sponge) to clean the soot. Take care not to put too much pressure on the sponge as this can permanently embed the soot residue into the pores of the finished wood.

Use Murphy Oil Soap or Wood Cleaner and a rag to clean all furniture.

If more agitation is required, you can use grade 0000 steel wool. Remember, if using steel wool, work only in the direction of the grain.

In extreme situations, you can use a weak dilution of Unsmoke Degrease-All. Rinse after cleaning.

Polishing after cleaning may be required. If you have used a degreaser at any point in the cleaning process, this step is necessary.

Cleaning unfinished wood affected by soot

Due to the different roughness and materials of unfinished wood and the different pressures and temperatures of the fire, you may need to try any or all of these suggestions. You usually want to seal the wood after cleaning.Basic procedure:

Remove all severely burned areas if possible.

Use Unsmoke 9-D-9 or FreshWave IAQ Air and Surface Spray, spray blocking all areas for initial deodorization.

HEPA vacuums all surfaces to remove dry soot.

Wipe all surfaces with a dry cleaning sponge (chemical sponge) to remove any amount of soot.

Use a degreaser (diluted according to label instructions), apply to untreated wood using a pump sprayer. Use a nylon brush to stir well. Rinse with clean water. Deodorant can be added to your cleaning solution for additional deodorization.

Sand down any heavily stained areas by hand. This can reduce or eliminate stains.

Create a heat mist for the area, using the right scent for your application:

Electric and plastic fires – Kentucky Bluegrass

Protein shot – Citrus / lemon

Natural Fire – Neutral (Odorless)

Combination or pungent smell – Cherry

If odor persists, use an ozone or hydroxyl generator in the affected area.

Read: how to clean wood damaged by smokeReplacement procedure:For large areas, you may want to skip the above recommendation in steps 1 to 6 and use a media blaster for faster results.

Furniture restoration

If the wood has been burned, it will likely need replacing.Direction:

Using a pump-up sprayer, apply Unsmoke Degrease-All diluted at 14-43 oz per gallon of water. Use minimal moisture when applying it.

Use a dry cleaning sponge to evenly remove the soot.

Using a rag, apply Woodcraft Cleaner to wood grained vertical and horizontal surfaces.

Leave Woodcraft Cleaner for 5 to 10 minutes to soften the soot.

Using 0000 steel wool, stir the surface with wood grain to gently polish away smoke stains.

Wipe off excess recovery solution with a cotton cloth. Wipe in the direction of the grain.

Using a rag, rub Unitex Luster Lemon Oil Polish onto the wood.

If the smell still persists, place the furniture in the ozone cellar and let it sit for 24-48 hours.

Read: how to clean smoke-damaged wood For more information or assistance in choosing products for your restoration, please contact Jon-Don Restoration Specialist at 800- 556-6366.

Last, Wallx.net sent you details about the topic “How To Clean Smoke Damaged Wood❤️️”.Hope with useful information that the article “How To Clean Smoke Damaged Wood” It will help readers to be more interested in “How To Clean Smoke Damaged Wood [ ❤️️❤️️ ]”.

Posts “How To Clean Smoke Damaged Wood” posted by on 2021-11-02 12:23:28. Thank you for reading the article at wallx.net