How To Build A Wooden Lamp Post

If you are looking for a stylish and unique way to highlight your home landscape, then look to the right. Made of rot-resistant western red cedar, the fixture includes a 2×4 center post to anchor it, a horizontal arm to hold the lantern, and a 1×6 backplate that connects the 2×4s together and creates attractive ball lines. Fitted with a beautiful copper and glass candle lamp, it exudes Zen beauty day and night. complement almost any outdoor space, from patios to waterfronts. If you want to wire up a light pole for low voltage lighting, he shows you how to do that too.SHOW: H. Potter Craftsman Lantern, 9¾ x 10½ inches, $80; H.PotterWatco Teak Oil Finish, $11 per liter; Rust-Oleum Download and print the lamppost cutting list

Step 1: Overview of the light pole

Illustrated by Gregory Nemec

Daily timeline

• Day 1: Cut to size and shape the cedar board (Steps 2-8).
• Day 2: Assemble the light pole and install it (Step 9-18).

Pathway light pole cutting list

• Post 2 × 4:1 @ 6 feet
• 2 × 4 cross weapons: 1 @ 12½ inches
• 2 × 4 cross weapons: 1 @ 3 inches
• 1 × 6: 2 @ 4¾ inch back panel with 45 degree bevel top
• Rear panel 1 × 6: 2 @ 36 inches
• 1 × 6 cross panels: 2 @ 27 inches with 1 inch nose and 45 degree angled ends
• 2×10 base trim: 2 @ 6 inches
• 2 × 10 base contour: 2 @ 7½ inches

Both pieces have a 45 degree chamfer at the top and are measured between the long points of the double layered endsDownload and print a cut list

Shopping list

• 2 × 4 ordinary cedar boards. Get an 8 leg to make the center post and the lantern arm.
• 1 × 6 clear cedar boards. Take two 8-foot lengths to cover the pillars.
• 2×10 clear cedar board. Get a 6 footer footer to wrap the bottom of the post.
• construction adhesive
• Finished nails are 2 and 2 inches long for a pneumatic nailing machine
• inch . hardwood pins
• -inch . diameter spade bit waterproof carpenter glue to glue the dowel bars in place
• polyurethane glue for gloved joints on decorative soles
• 100-grit disc for random orbit sander
• 1 inch screw hook to hang lanterns or fixture lights
• copper candle lantern
• low voltage ground lighting equipment (optional)
• transformers (optional)
• 12 volt . cable (optional)
• cable stapler (optional)

Step 2: Cut the 2×4 diagonal to Length

Kolin Smith’s photo Switch to crop list. Use a sliding compound cutting saw to cut the 2×4 diagonal into three lengths: the long vertical post in the center and the two shorter pieces that form the core of the lantern arm.

Step 3: Cut out the end of the post

Photo by Kolin Smith Set the cement saw blade to its sharpest angle (some are 55 degrees) and cut the bottom end of the center post. The resulting spike will allow you to hit the pole to the ground later with a sledgehammer.

Step 4: Cut the wire channel

Photo by Kolin Smith Follow this three-step sequence if you are going to connect a low voltage landscape lighting device. Otherwise, proceed to Step 7. Mark the centerline of the column from where it will land to its intersection with the light arm, 6¼ inches from the top of the column. drill a hole ½ inch deep at that intersection. To create a channel, place the circular saw blade ½ inch deep and make several cuts parallel to the centerline, no more than ¼ inch to either side. Do the same from the hole drilled towards one edge of the board. lantern arm, follow the same process to continue channel from post; Drill a similar turning hole 2 inches from the top, and cut a groove in the edge to access the lantern.

Step 5: Remove waste wood

Photo by Kolin Smith Using a wood chisel to pry the waste wood out of the canal and scrape it off.

Step 6: Put the cable in the slot

Photo by Kolin Smith Read more: how to build a chippendale handrail Thread the low voltage power cable into the trench, making sure to leave a few feet at the lamp arm. Use staples to secure the cable in place. Note that a 12-gauge low-voltage cable is sufficient for most landscape lighting systems with a total output of 200 watts or less.Tip: Adjust your combo square to the distance between the edge of the post and the edge of the channel, and use that setting to avoid puncturing the cable in Steps 9 and 18.

Step 7: Mark the arms 1 × 6

Photo by Kolin Smith Cut two 1×6 boards to fit the lantern arms. Use a combination square to mark a 45-degree cut on each end of both diagonal bars. Position the lines so that the 1 inch of the table tops remains square.

Step 8: Cut pieces

Kolin Smith’s photo Set the saw to 45 degrees and cut the arms at the cuts you marked. Next, you will cut 4 1×6 planks to cover the center pillar. First, bevel one end of each plate at 45 degrees and use those ends to form short segments that will fit snugly over the lantern arms.

Step 9: Arrange the cladding layer

Photo by Kolin Smith On a flat work surface, arrange three 1×6 pieces to form one side of the lamp post, as shown.

Step 10: Positioning 2 × 4 . Parts

Photo by Kolin Smith Place the post in the center 2×4 on the board. To center it, use a 1-inch-wide block of wood chips and move the 2×4 block until it is flat with one edge of the 1×6 block. Mark the end position of the 2×4 block with a pencil. and repeat the process for the lantern arm.

Step 11: Join parts of the post

Photo by Kolin Smith Remove the center post and arms, apply construction glue to them and press them to the contours on the backplate. Drive the 2×4 pieces with a pneumatic finish nailer and a 2-inch long nail. If you installed the power cable in Step 4, be sure to keep the latches within 1 ½ inch of either side of the 2×4. Apply construction adhesive to the 2x4s contacts and place the remaining backing on. location; use your combo square to align it with the opposite cladding. Press the tables down. For added strength, this coating can be secured with a pneumatic finish nailer and a 2-inch long nail. If you do, make sure to fill and sand the nail holes.

Step 12: Hole Dowel

Kolin Smith’s photo To strengthen the connection between the pillar and swingarm of the lantern — and to give the product a handcrafted beauty — install two hardwood pegs. Use a combination square to draw a 45 degree line where the pillar meets the arm. Make two marks along the line, 2 ½ inches from each corner Read more: how to match your friends on a super mario run Slide a chipboard under the joint, then use a drill and drill bit diameter ⅜ inch to drill two holes at the Marks; go completely to the other side.

Step 13: Cut off the threads

Photo by Kolin Smith Waterproof carpenter glue or polyurethane glue onto ⅜ inch hardwood dowels. Touch the pin into one of the holes until it sticks out at least ⅜ inch from the opposite side. Trim off the excess pin with a Japanese hand saw, as shown. Cut the remaining hole and trim the excess.

Step 14: Bevel-Rip the sole

Kolin Smith’s photo Glue the 2×10 cedar board onto a sturdy surface with the long protruding edge. Use a circular saw to cut a 45-degree bevel along that protruding edge.

Step 15: Cut the base into small pieces

Kolin Smith’s photo: Tilt the saw blade to a 45 bevel and adjust the bevel to zero. Cut the 2×10 bevel into 4 lengths to wrap around the base of the lamp post.

Step 16: Attach the base to the article

Photo by Kolin Smith Apply construction glue to the back of the first base trim and press it to the lamp post, square end flat with the end of the backplate. Use the pneumatic finishing nail and the 2 ½ inch long nail to attach it, then Attach the remaining three base pieces in the same manner. Use construction glue against the column, but apply waterproof carpenter’s glue or polyurethane glue to each of the four corner joints with two layers. And make sure to nail through the corners, as shown.

Step 17: Submerge the post

Kolin Smith’s photo: Place a 2×4 block on top of the center post and tap the spike with a 3-pound sledgehammer. If necessary, plow the soil first with a shovel. At least a third of posts should extend below ground level. Use the 2-foot height to pull the pole. Treat it with teak oil if you want to keep the color.

Step 18: Hang the Lantern

Photo by Kolin Smith Screw a 1-inch screw hook into the underside of a 2×4 arm and hang the candle from there. connect.Read more: How to Eat Tostada | Top Q&A

Last, Wallx.net sent you details about the topic “How To Build A Wooden Lamp Post❤️️”.Hope with useful information that the article “How To Build A Wooden Lamp Post” It will help readers to be more interested in “How To Build A Wooden Lamp Post [ ❤️️❤️️ ]”.

Posts “How To Build A Wooden Lamp Post” posted by on 2021-10-20 05:22:12. Thank you for reading the article at wallx.net