How To Build A Sideboard From Stock Cabinets
Dishes, serving pieces, tablecloths — a dresser that packs a lot of storage space in a relatively small footprint, making it a handy addition to any household. A sturdy, high-quality cabinet can leave thousands of dollars behind in your finances, but as Tom Silva, the general contractor of This Old House, has proven, you can improve a few kitchen cabinets that can save money. molded base, footrest and handle for handmade production at a fraction of the cost of buying a ready-made one. Choose unfinished 15- or 18-inch cabinets that come with openable doors and drawers (not the fake drawer fronts used for sink cabinets) and take a day to put all the pieces together. together. Your beautiful creations will stand out at dinner parties for years to come. Valspar. Rub the n’ Buff metallic finish in antique gold; Amaco.
How to turn a kitchen cabinet into a side cabinet?
Contents
Illustrated by Jennifer Stimpson Flipped feet and ridges add decorative flair to your finished piece. You will find all the materials you need at any major home center.
Cut list
(download plan here)
- a inch . cabinet-grade birch plywood
- three 18-inch base cabinets
- Network range ½x1
- molded bed
- 1 × 3 feather strips
- Network range ½x2
- three push door latches
- six buttons
- four feet
- four corner foot plates
Shopping list
Step 1: Delete Toekick
Photo by Wendell T. Webber Read more: how to wire the starter button on a lawn mower To shorten each drawer to fit the legs, move a line equal to the bottom edge of the face frame to the levers, sides and face back of each drawer using a matching square. Remove excess material with a hand saw.
Step 2: Fasten the cabinets together
Photo by Wendell T. WebberSandwich two 1×3 fur strips between drawers vertically to act as padding. Using a drill/driver and 1 5/8 inch deck screw, fasten the cabinets together along the length of the strips, sinking the screws from both sides for added sturdiness.
Step 3: Hide the end
Photo by Wendell T. WebberNail two 1×3 fur strips lengthwise to unfinished ends of paired cabinets, front and back. If the edge of the face frame extends beyond the side, place the front fur strip behind it, as shown here. Using a circular saw, cut two pieces of cabinet-grade plywood to cover all sides of the assembled cabinet. Use finishing nails to secure them to the strips. Together, the fur strips and plywood on the sides create enough cabinet ends to fit the space between them.
Step 4: Cover the front
Photo by Wendell T. Webber Cut a ½x1 lattice strip 1 inch longer than the width of the connected cabinets. Mount it horizontally, on the bottom edge of the drawer, using the finishing nails. To cover spacers and exposed plywood edges between drawers and at the ends, attach x2 slats lengthwise cut to size above and below the strip you just attached.
Step 5: Attach the foot plate
Photo by Wendell T. Webber Screw the foot plates to the bottom of the cabinet corners.
Step 6: Screw on the legs
Photo by Wendell T. WebberRead more: how to make a pointed bra Step your feet on the plate until they fit. Carefully flip the piece of cake upright, placing it on its feet.
Image by Wendell T. Webber Pierce two holes for the knobs in each drawer, making sure they are centered vertically and about 4 inches from each end. Hold each knob in place as you tighten the screw from inside the drawer.
Step 8: Attach the door latches
Photo by Wendell T. Webber On the inside of each drawer, towards the top, close a block to the back of the faceplate where the push pin will go. Screw the latch into place so that it is flush with the front of the frame, then screw the corresponding magnetic plate into the inside of the door.Tip: To properly position the magnetic plate to the inside of the door, color the back of the plate with chalk, lipstick or highlighter, then glue the magnetic plate to the latch, marking side facing out. When you close the door, the ink plate will leave a small mark on the inside of the door where the plate is located.
Step 9: Go to the top
Photo by Wendell T. Webber Using a circular saw guided by a straight fence, cut a piece of plywood to the width and depth of the piece, including the slats on the front and finished sides. . Secure the top over the frame of each cabinet with a finishing hammer and nail. Place the nail underneath the wood surface with a set of nails.
Step 10: Cut off the head
Use finishing nails to fix the bed frame, with grooves in the corners, sides and front edges of the baseboard. Fill in any seams and tie holes with a wood scraper.
Step 11: Sand and paint the piece
Photo by Wendell T. WebberBay smooth the surface of the wood planks with medium sandpaper. Apply two coats of paint or stain and let dry completely. Highlight details with metallic wax finishes, such as Rub ‘N Buff. Read more: How to tell if a sausage is cooked
Tools:
Last, Wallx.net sent you details about the topic “How To Build A Sideboard From Stock Cabinets❤️️”.Hope with useful information that the article “How To Build A Sideboard From Stock Cabinets” It will help readers to be more interested in “How To Build A Sideboard From Stock Cabinets [ ❤️️❤️️ ]”.
Posts “How To Build A Sideboard From Stock Cabinets” posted by on 2021-10-30 02:47:14. Thank you for reading the article at wallx.net
