How do I change my band on my Fitbit Versa or Sense? Learn the steps

Need or want to replace your Fitbit Sense or Versa wristband (Versa, Versa 2, Versa 3, or Versa Lite) but can’t figure out the correct way to remove your current band? Those who want to customize their smartwatch, changing the strap is not one of the “easy” things. If that’s you, read on for best practices and tips for changing out your Fitbit Versa strap.

Related reading

• Is Fitbit irritating your skin or causing a rash? Let’s fix it!
• Find your Fitbit serial number
• How do I repair or replace my Fitbit under warranty?
• Contact Fitbit customer support for issues and warranty information
• 5 Best Fitbit Versa Chargers (Versa/2/3 and More)

How to change your Versa or Sense bracelet

Through trial and error, we’ve found that the best way to change a Fitbit strap is to place the Versa (or any Fitbit tracker or smartwatch) face down on a flat surface. changing the glasses makes sure you see the clasps or buttons of the strap! Your Fitbit Versa or Sense comes with two detachable straps – an upper (top) and a lower (bottom) strap. The bands connect to the Fitbit cobblestone with a pin or a button, depending on the model.

• Newer Fitbits like the Sense and Versa 3 have an updated strap system that uses buttons.
• Older Versa models (like the Lite or 2) have a small pin that allows you to remove and reattach the bands.

You only need to change the bottom band if you are switching between small and large bands for the same look.

How to remove the wristband from your Fitbit Sense or Versa 3

Read more: How to Draw Hips Simple: Best Drawing Tutorials | FAQs back to top Before you can use a new band, you will need to remove the old tape. To do that, flip your Sense or Versa 3 upside down so the charging pins and heart rate monitor are facing you.

Rotate your Sense or Versa 3 on the back and place it on a flat and clean surface

Locate the strip release button for the bottom band

Press and slide the button down towards the strap to release it

Keep pressing the button and with the other hand, gently pull the strap away from the Fitbit pebble

If you want to replace the entire strip, repeat these steps for the top of the strip.

How to remove the wristband from your original Fitbit Versa 2, Lite or Versa

First, turn your Versa upside down so the charging pin and heart rate monitor are facing up.

Turn your Fitbit over and place it on a clean, flat surface

On the bottom strip, locate the quick release lever’s latch

Press this pin inward and slide the band gently to the opposite side to release the pin from the watch

Once the lever has been pushed in, this means the band is released from the Versa’s handle. Pull the other side of the pinout away from the body of the Versa.

Repeat on the other side, if changing the entire strip

The benefit of removing the Fitbit wristband is that you want to tilt the strap slightly so that the other end of the latch slides out. It can be frustrating at first, but it can be done by going through the instructions carefully.

How to change the strap on your Fitbit Versa or Sense

Install your new Sense or Versa band!Now that your old band is gone, you are left with only your new body and band.

For newer models like Fitbit Sense and Versa 3

Strap replacement on these models is a lot easier than on previous models, such as the Versa 2! Read more: How to get revenge on someone who fooled you Before you begin, clean the ends of your band and gently wipe the inside of the groove where the band enters your Fitbit. To attach the strap to your Sense or Versa 3, push the ends of the band into the Fitbit cobblestone end grooves until you hear a click and the strap snaps into place. If you are replacing the entire strap, keep in mind that the strap has loops that are attached to the top of the watch. However, you can switch this position if preferred—both ends will attach to either side of your Fitbit pebble.

For older Versa Series, follow these instructions

Read more: How to get revenge on someone who’s haunted you Before you begin, clean the ends of your band and gently wipe the inside of the groove where the band enters your Fitbit.

Locate both hold the latch and quick release leverage on each side of your new band

To attach a new strap, hold the strap at a 45° (A) angle.

Slide the band retainer into the groove on your Fitbit device (B)

Press the quick release lever in and push & slide the other end of the strap into position (C)

When both ends of the latch are inserted, release the quick release lever

Repeat these steps for the other side and voila. You’ve installed your brand new Fitbit Versa strap, made it up, so you’re now stylin’ and profilin’. Or, you know, just go to the gym.

Having trouble replacing your Fitbit Versa band?

Check out Fitbit’s video on how to switch straps on your older Fitbit Versa model!

Inference

As we said above, the Fitbit Versa is one of the best smartwatches on the market and you really can’t go wrong. But we want to hear from you! Let us know in the comments if you’ve decided on a new band for your Versa and which band you’ve chosen. Also, if you run into problems, don’t hesitate to leave us a comment and we’ll be more than happy to help alleviate these issues! Read more: How to add money to apple pay without a debit card

Last, Wallx.net sent you details about the topic “How do I change my band on my Fitbit Versa or Sense? Learn the steps❤️️”.Hope with useful information that the article “How do I change my band on my Fitbit Versa or Sense? Learn the steps” It will help readers to be more interested in “How do I change my band on my Fitbit Versa or Sense? Learn the steps [ ❤️️❤️️ ]”.

Posts “How do I change my band on my Fitbit Versa or Sense? Learn the steps” posted by on 2021-08-15 14:46:12. Thank you for reading the article at wallx.net