Crocheting A Tube | Top Q&A

Hook in tube: Two ways

Crocheting in a circle – as in the case of small squares – tends to be an easy and simple skill to learn. On the other hand, crocheting in a pipe is a bit more complicated, as maintaining the proper number of seams requires a little more skill and attention. The first method is step tube, where each loop is worked as an individual part. The next round is then “upgraded” using chain stitches and worked as another individual piece. The second method is spiral tube, made in a similar way to crochet, each method has its pros and cons. Your best bet is to practice both with a basic stitch you’re comfortable with to see which stitch you like better. If you don’t have a preference, many times, templates will also tell you which method to use depending on the designer’s end result.

Method one: Stepping tube

Step 1 / Slide the button onto your hook. Hook in whatever sequence your pattern requires. In my sample I made 20 strings. Remember not to count the chains on your hook.Read more: how to install auxiliary fuel tankStep 2 / Take care to make sure that all the Vs of the string point in the same direction. (If you’re used to knitting circles, this is the same concept as “be careful not to twist the stitches.”) Place your hook on the first chain. Do the Slip Stitch, (yo, pull through the loop on the chain, then loop on the hook). Your string is now connected into a pipe.Step 3 / Thread the number of stitches needed to create the stitch pattern you are using, as if you were manipulating it back and forth. (We’re knitting single crochet here, so I’m working ch 1) This chain counts as one stitch. Read more: How to get bigger handsStep 4 / Hook each stitch around, making sure you have the same number of stitches as you originally strung. Don’t forget that you’re counting the string(s) from Step 3 as your first stitch. Note: I’m knitting in the back loop for this round, which can sometimes make the chain stitches appear a bit loose, especially in the case of larger gauge yarns.Step 5 / To complete the round, make a slip stitch into the top of the chain at the top of the loop.Step 6 / To work a second and all subsequent rounds, repeat Steps 3-5 for the length you want. However, it is beneficial because it makes it very easy to maintain the proper number of stitches as each round is its own unique process with a defined start and end. The picture above left shows a finished 7 loop tube with a hidden seam in the back. The image on the right above shows the same tube, but with a front and center seam.

Tube method: Spiral tube

Steps 1 and 2 of Spiral Pipe are the same as Pipe Steps: Step 1 / Slide the button onto your hook. Hook in whatever sequence your pattern requires. In my sample I made 20 strings. Remember not to count the chains on your hook.Read more: how to install auxiliary fuel tankStep 2 / Take care to make sure that all the Vs of the string point in the same direction. (If you’re used to knitting circles, this is the same concept as “be careful not to twist the stitches.”) Place your hook on the first chain. Do the Slip Stitch, (yo, pull through the loop on the chain, then loop on the hook). Your string is now connected into a pipe.Step 3 / Chain 1, then knit 1 stitch in the same gap as the loose seam. Note: This step is only done at the beginning of your work.Step 3a / You may find it helpful to place a marker here to identify the first seam in the loop. It can be very helpful to count down to ensure that you have made the correct number of stitches in each round.Step 4 / You may find it helpful to place a marker here to identify the first seam in the loop. It can be very helpful to count down to ensure that you have made the correct number of stitches in each round. Single hook on each remaining stitch. Note: Like with the Stepped Tube, I’m hooking to the back loop for the first round.Step 5 / When you reach the marker set in the previous step, delete the marker. Make a single crochet stitch into the marked stitch, then replace the marker with the stitch you just made. Single crochet into each previous single crochet stitch until you reach the end of the loop. The picture above left shows a finished 7 loop tube with a hidden seam in the back. The image on the right above shows the same tube, but with a seam in the front. If you look closely, you’ll notice the starting point of each round is moving to the right at a slight angle. Build a roll pot. Unlike knitting, since there’s no stitch directly on your hook, you can easily gain or lose stitches, that’s why we recommend placing a marker on the first stitch of each loop. so you can make sure you always have the correct amount of stitches until you’re really comfortable “reading” your work. Read more: how to make crab with butter sauce