How To Cut A Circle In Glass Without A Circle Cutter
No need for circle cutters
Cutting stained glass circles can be done easily with basic stained glass equipment. Expensive circular cutters can help – and they work, but here you’ll learn how to cut perfect circles with just one cutter and a pair of cutter/grooving pliers. Not even a grinder! The cutter I use is the Comfort Grip Supercutter by Toyo and the pliers are the Studio Pro 3/8-inch Breaker Grozer. a cut with your cutter before you get started with this stained glass circle cutting tutorial. If you don’t feel confident with this, there are plenty of tips that will help you get better. Including circles! Classes are self-paced and online, so you can learn these methods even if you can’t make it to class. You can see if it’s right for you here Conquer the Curves.
Glass circle cutting video
1 Getting Started with Cut Stained Glass CirclesCut the circles first
- Draw your circle on art glass with permanent marker
- Put some linoleum or newspaper underneath to cushion it from the pressure
- Wear safety glasses
- Make your first cut by going in from one side, following a circle around and out of the opposite edge
- As always with cutting, make sure you keep pressure consistent along the entire length of the point line so you get a good rest.
2 Open the clipUse your thumb to open the score
- Turn the glass upside down so that the cut line (or scoring line) you just created is below
- Press firmly along the number line with your thumb until it opens
- You should see the cut ‘open’ out along its length. It will start to look shiny and as if it’s cracked
3 Separation of cuts – Method 1Split the scoreline with your thumb
- Turn the glass over, so that the number line you drew is on the glass
- Place your thumbs on either side of the line where your point line ENDS. It’s best to start opening the cut from this end
- Easily separate the two pieces of glass by gently rocking your wrist back and forth
- If the score is only half open, you can repeat this swinging action starting from the other side (where you started the cut)
- Make sure you hold it firmly underneath with both hands as you do this
4 Split the cut – Method 2 Repeat 1-3 on the other side of the circle. These alternative methods for cutting circles with stained glass are great if your thumb is not strong.Use the grooving machine to press the cut line
- If you cannot press with your thumb for any reason, you can use the handle of the cutter/grooving pliers to open the score line.
Use a chisel / burr to loosen art glass Read more: how to pass the vcla writing test Pliers can be used to separate glass:
- Make sure that the function is flat above
- Place the end of the jaw along the cut where you ended the track and bend it gently downwards, making sure you’re holding it firmly.
- If the glass doesn’t break, switch to the other end of the track and repeat, this time with more ‘snap’ movements
- Your art glass will now shatter into a clean piece
5 Cut out the circles with stained glass – Faces Now for a little more complexity – two slits on the sides. Do not use close pressure to open the score when you have only a small amount of glass on one side. It is easier to use pliers.Use grooving pliers for smaller bits
- Choose one of the fronts
- Scoring along the remaining bit of the circle with a cutter
- Using grooving pliers, align the flat jaw along the cut and ‘flip’ as much as you can with a short, sharp downward motion
- Keep your fingers underneath close to the pliers to keep them in place
6 Remove debrisRemoval of small debris Cutter/grooving pliers leave behind small pieces of glass that need to be removed. This is done in two ways and you will probably need to use both.Snapping If the small pieces are large enough for you to grasp with slotted pliers, you can break them apart, as in 5 above. Grozing If they are more stubborn, the rounded knobs make the edges uneven, you need to ‘clean’ them up.Grooved circle edges
- Hold the circle below with your free hand
- Place the flat jaw part of the pliers over the uneven edge and scrape them down and around the edge
- The internal serration of the grooving jaw will ‘chisel’ or gnaw uneven pieces. This needs some practice.
- You must wear goggles for this. ‘
7 Finished Glass Circles And there you have it, a perfect circle. And all without using expensive circle cuttersCompleted CircleRead more: how to play level 130 on candy crush | Top Q&A If you need a little more help with your cutting, I wrote ‘Cut perfect curves‘ just for you. It is a Free eBooks that shows you how to avoid making mistakes by learning from all the costly mistakes I’ve made over the years! To get it, sign up below to receive the Stained Glass Everything Newsletter and the ‘Cut Perfect Curves’ e-book will magically appear in your inbox, along with all the other great tips and inspiration. They are easy to use and the results are very good. Visit the main tutorial page to see all other Stained Glass Cut tutorials. servants
Last, Wallx.net sent you details about the topic “How To Cut A Circle In Glass Without A Circle Cutter❤️️”.Hope with useful information that the article “How To Cut A Circle In Glass Without A Circle Cutter” It will help readers to be more interested in “How To Cut A Circle In Glass Without A Circle Cutter [ ❤️️❤️️ ]”.
Posts “How To Cut A Circle In Glass Without A Circle Cutter” posted by on 2021-10-30 21:45:33. Thank you for reading the article at wallx.net