How To Do File Work On A Knife

Step by step instructions in the photo

Contents

Vine filework is my favorite profile style. If you break it down into small steps, it’s very easy to do. The materials you will need are a Sharpie® marker, vise, and a 5/32 inch round file and a small triangle file. You can use a larger round file on thick-edged materials, or a smaller round file when engraving thin backing or blades. sharper than the other two corners. This provides a safe left and right side to open your grape file cuts, as well as give them sharp points.

STEP 1

Using your Sharpie® marker, make semicircular marks approximately 5/16 inch apart down one side of the blade spike. (Though not shown here, make sure to keep the blade firmly in a visor.) (Hayes photo)

Step 2

Master Blacksmith Wally HayesFile the marked face with the round file at a 45 degree angle. Smash in the spine, stopping right in the middle of the blade. (Hayes photo)

Step 3

File processing techniquesUsing a marker, mark down the other side of the blade spike in between the notches. (Hayes photo)

Step 4

Read more: How to make a man cry in the bedroomFile the knife spineFill in another row of half-ring notches on the “new” side. Remember to hold the file at about a 45-degree angle and stop filing right at the center of the blade. (Hayes photo)

Step 5

Manual profile makingNext, take your triangle file and place it next to one of the notches. I leave about 16 inches between the semicircle and the triangle that I will cut. Tilt the file so that the cut is closest to the perpendicular groove (90 degrees to the blade). This gives you a straight line into your cut and a rotation away from the cut. (Hayes photo)

See Also  How long to cook steak on george foreman grill medium

Step 6

Filing techniques for knittingRotate the blade around in the lens and cut the “V” notches in front of the remaining semicircular notches. (Hayes photo)

Step 7

Knife ProfileTake the triangle file and file the corner of each semicircle, creating a gentle curve that opens up to one side of the semicircle. (Hayes photo)

Step 8

Read more: how to turn off auto androidTechniques for file machining knivesOpen the remaining sides of the half-ring grooves. In both cases, they are in front of the “V” notches. Here’s how I remember so I don’t get confused. (Hayes photo)

Step 9

How to tap a knifeNow let’s move on to the “V” notch. Open one side of the anterior tongue spine. File the “V” groove to create an even arc to the edge of the blade spike. If you don’t twist the file in your hand when filing, you will get a flat mark. GO SLOW AND EASY. (Hayes photo)

Step 10

Working knife fileTurn the blade around and open the “V” notches on the other side of the spine. Remember that the “V” notch is only open on one side, behind the notch. 90 degree safety side is not touched. (Hayes photo)

Step 11

Backbone art fileTake the safe edge of the triangle file and file into each point of the “V” groove. File it into a sharp, clear point. (Hayes photo)

Step 12 (Finally)

For the 12th and final step, re-scan the entire profiled area with fine sandpaper. Increase the strip of 320 grit sandpaper to 3 inches and place the paper over the circular and triangular file to back the paper. Do not push too hard and tilt the wrap away from the safety edges so that you do not round (square) the safety corners of the profile. Have fun and stay safe. Read more: How to cope

See Also  How To Stop Reusable Pads Smelling

Read on:

  • Fit and Finish 101: How to Tell When You See It on a Knife
  • Knifemaking: Building a Processing Framework
  • Craft a knife by smelting an Iron Bog
  • Best knife-to-blade handling ratio
  • Meet living legends who make knives

Last, Wallx.net sent you details about the topic “How To Do File Work On A Knife❤️️”.Hope with useful information that the article “How To Do File Work On A Knife” It will help readers to be more interested in “How To Do File Work On A Knife [ ❤️️❤️️ ]”.

Posts “How To Do File Work On A Knife” posted by on 2021-11-05 06:55:13. Thank you for reading the article at wallx.net

Rate this post
Back to top button