How To Install A Wall Hung Toilet Bowl

Usually, the toilet is mounted on the floor. In these cases, the waste pipe runs through the floor, and the water supply pipe goes from the wall. Without a doubt, a floor-to-ceiling toilet has a lot of benefits. However, it also has disadvantages, for example they tend to accumulate deposits on grout joints that come into contact with the floor. However, that won’t happen with wall-hung toilets. They do not touch the floor because they are fully supported against the wall. mounted units. Today, we prepared a step-by-step guide to show you how to install a wall-mounted toilet like a pro.

How to install a wall-mounted toilet?

1. Previous Steps

Before starting the installation, you need to turn off the water supply. Then uninstall your old toilet. To do this, first drain the tank and remove the connector of the toilet bowl. Then, use a hammer and chisel to break the grout that sticks the toilet to the floor. Then you will need to relocate the waste pipe. Finally, seal the hole in the floor.

2. Assembling the mounting bracket

Then assemble the frame where the toilet will be mounted. To do this, join the bars forming the frame as explained in the instruction manual. Then, install the tank brackets and drain pipes. Finally, attach the tank to the frame.Use a small torque wrench to secure all pins in place. Then, install the metal pins of the frame and plastic clips to secure the waste pipe.

3. Mark the wall and floor

First, draw a vertical line 1.08 m on the wall starting from the ground. This line should coincide with the midpoint of the exhaust pipe. Draw perpendicular lines on the first line as 1m (second line) and 1.08m (third line). Then make two marks on the third line, 235 mm to the right and left of the vertical line.Position the frame, so that the 90 degree elbow of the waste pipe is inserted into the plastic clamp. Mark each point where the mounting holes of the frame come into contact with the floor. Then remove the mounting bracket before moving on to the next step, check that there is a minimum gap of 230 mm between the frame and the wall.

4. Install the mounting bracket

Drill holes in the wall and floor with a 10mm drill bit. Then insert the plastic anchors inside the holes. Position the mounting bracket in place, with the metal feet supported on the floor. Secure the frame to the floor with screws. Read more: how to write a love song for someone you loveConnect the end of the frame and the support with a threaded rod. Then, secure the brackets to the wall with screws. Finally, rotate the threaded rod to correct the vertical alignment of the frame. Use a bubble level while doing this.

5. Install the discharge mechanism

Remove the red plastic handle from the tank. Then, remove the plastic cover covering the water connectors. Install the stop valve on the water outlet coming from the wall. The outlet of the stop valve should point to the right. Be sure to apply enough Teflon tape just to prevent leakage.Insert a hose into the outlet of the stopcock. Then make sure the stop valve is closed. Turn on the bathroom water supply and check that there are no water leaks. Place the other end of the hose in a bucket and open the stop valve to verify water pressure. Then, close the valve. Then, connect the free end of the hose to the inlet thread of the drain mechanism. Finally, install the test shaft. The problem is that if the flushing mechanism malfunctions in the future for such toilet systems, you will need to open the wall to repair it with a kit.

6. Drywall Installation

Cover the front, sides and top of the installation frame with drywall. Be sure to cut the drywall where the toilet fittings are installed.

7. Install the toilet

First, connect the exhaust pipe with its seal. Then, install the drain pipe into the toilet bowl. Mark the pipe at the point where it protrudes from the bowl. Then, install the exhaust pipe to the exhaust. Mark the exhaust pipe at the point where it protrudes from the exhaust manifold.Measure the length from the edge of the tube to each mark. Then add both lengths and add 5 millimeters. Cut the exhaust to that length. Then use a piece of sandpaper to smooth out the contours of the pipe. Finally, install the exhaust manifold to the exhaust manifold.Screw the threaded rods that support the toilet bowl to the mounting bracket. They should protrude 6 cm from the frame. Finally, install the toilet, threading the threaded rods through the mounting holes. Use washers and nuts to secure the toilet in place. Check that the top of the bowl is completely horizontal using the bubble level.

8. Install the discharge plate

Read more: How to dehydrate broccoliUse a utility knife to cut the plastic cover of the drain disc. Then, mount the brackets of the flat sheet on the drywall. Install the air plug on the plate and then connect it to the blue hose of the exhaust.Finally, open the stop valve and install the drain plate into its holder.

9. Final Steps

Press the air button to verify the toilet’s operation. If everything is fine, pour silicone glue on the sides of the bowl. Finally, install the toilet stopper.

Inference

As you can see, wall-hung toilets are a great alternative to conventional toilets. They are easy to clean and do not accumulate too much litter. Certainly, installing them is not easy. However, if you carefully follow these installation instructions, you have nothing to worry about.

Frequently asked questions

Q. 1: Why should I install a wall-mounted toilet?Answer: Wall-hung toilets are elegant, compact and easy to clean. In addition, they do not leave stains on the floor like conventional toilets.Q. 2: How much does it cost to install a wall-mounted toilet?Answer: The average installation cost of a wall-mounted toilet is $600-$700.Q. 3: Does the Saniflo toilet have an odor?Answer: If the toilet is well ventilated, it will not produce bad odors. If your Saniflo toilet smells, it means something is not working properly.Q. 4: What is the average lifespan of a macerator toilet?Answer: These devices typically have an average lifespan of 10 years. However, they can last a lifetime if used properly.

Last, Wallx.net sent you details about the topic “How To Install A Wall Hung Toilet Bowl❤️️”.Hope with useful information that the article “How To Install A Wall Hung Toilet Bowl” It will help readers to be more interested in “How To Install A Wall Hung Toilet Bowl [ ❤️️❤️️ ]”.

Posts “How To Install A Wall Hung Toilet Bowl” posted by on 2021-10-30 18:55:31. Thank you for reading the article at wallx.net