5 BIG Shower Niche Install Mistakes To Avoid In Your Shower Remodel

It’s really scary how many shower niche installation errors can happen in a typical shower remodel, especially if your contractor is building you a custom shower niche. or have completed the niche, you still have to follow some rules and processes. correct a second This is Steve from SKG Renovations with some must-know tips to avoid making these 5 BIG shower installation mistakes on your next shower remodel. Niche Guide.

5 BIG mistakes:

Contents

Don’t skip the waterproof layer

Do not install a retrofit Niche

Make sure it integrates with the Waterproof Membrane

Don’t compromise the wall structure

Do not install on external wall

Extra tip: Improper installation of the shower stand

Don’t skip the waterproof layer

If you plan on installing a custom shower nook into your bathroom wall and you want to avoid making one of the biggest shower installation mistakes, you must make sure that you or your home Your contractor does not forget the waterproofing step. Well built, it can look very sturdy, solid and waterproof. This is an assumption made all too often when shower recesses are framed into the shower wall. You’re probably thinking that leaks like this seem unlikely if the recess is properly tiled & plastered after construction, and you’ll be right… for a while. The constant exposure to water and frequent temperature changes make the bathing environment quite uncomfortable. These environmental pressures cause all parts of the shower assembly to move slightly, mainly due to expansion and contraction. It usually starts as very small cracks in the corners that you can’t easily see. But even the smallest cracks will allow moisture to penetrate, moving easily through the seams of the backboard, to the frame below. The rest you can imagine; wet walls lead to mold, dry rot………………. That you can easily avoid. Whether you or your contractor uses a sheet or liquid waterproofing membrane, it doesn’t matter, as long as you don’t skip this important step during your next bathroom remodel! More on bathroom waterproofing: Shower Membrane Waterproofing – The Ultimate Guide

Do not install retrofit showers

If you decide to install a pre-manufactured or finished shower niche instead of a custom-built niche, you can avoid a mistake when installing another shower niche by making sure that you Never install a retrofit shower niche. During the new bathroom remodeling project after the bathroom wall tiles have been installed and scrubbed. The tiles are then glued to the bathroom wall as usual, but the hole is left exposed so that a retrofitted shower niche can be installed later. . A silicon bead around its circumference will complete the installation. Does that make sense to you? If you said no, you would be right. It might seem like a slightly easier way to install a shower niche, but it’s not really that much easier than those membrane-bonded finished shower niche products and it’s violates industry “recommended best practices”. It’s really not worth the risk.

See Also  How to air fry carrots

Make sure it integrates with the Waterproof Membrane

To avoid mistakes when installing this HUGE shower niche, you must choose a shower niche with a built-in waterproof membrane bonded flange as shown in the two examples above. This fitting is made from sheet stainless steel with a brushed finish so no tiling is required. The membrane bond flange mounts on the backboard surface with screws and the waterproof membrane is attached to the top surface of this flange (as seen in the Image above). The other niche shown is a tiltable foam bath niche featuring a 1/2″ thick foam perimeter flange that also serves as a mounting flange and a membrane bond flange similar to a stainless steel niche. must be mounted on the frame rather than on the baseboard surface, so that the 1/2″ flange can co-align with the 1/2 thick tiled board surrounding it.These flanges are important to maintain integrity. integrity of the shower wall waterproof membrane More information on bathroom waterproofing: Waterproofing with a bathroom membrane waterproofing – The definitive guide

Don’t compromise the wall structure

Another BIG mistake among bathroom installation mistakes, is the construction of a custom tiled niche that compromises the structural integrity of the shower wall. example of this appropriate type. These horizontal niches are the epitome of luxury, sometimes extending an entire shower wall and providing a large area for storage.Dashed long alley - Stock photoMost of the horizontal recesses are built into the rear shower wall; It is usually the longest and, therefore, the most versatile wall in the area surrounding your bathroom. Either way, cutting a horizontal line out of the structural elements of this wall to make room for a niche is a dilemma. The problem is that these measures mainly deal with the structural stresses applied from above, but do not usually address the increase in flexibility (decrease in stiffness) due to longitudinal frame ablation. the possibility of mortar cracking, brick peeling and damage to the waterproofing membrane. Some contractors do not even install the required minimum surrounding structure, which profoundly affects the structural rigidity of the wall.

See Also  How To Let Air Out Of Tire

Build a new wall for your niche

If your new niche will span more than a few wall studs, the safest way to build your shower niche into this wall is to build a new wall adjacent to it, to accommodate the niche. This new wall allows you to build/fit your custom shower niche with minimal support above the new niche because the entire wall is anchored to the nail wall behind it. Super strong, super strong and super safe, because the original wall structure is completely intact. In my opinion a typical structural header structure and dowel assembly may still be acceptable in some cases if the wall is not structural, but the assembly must be perfectly constructed. . There is nothing safer than the parallel wall design I mentioned above. Talk to your contractor about it, because it is extremely important that you avoid mistakes when installing this large bathroom.

Do not install on external wall

This installation is often a big mistake when installing a bathroom niche as moisture can easily condense behind your niche if you do not do this installation correctly. Not the wall facing the outside. The problem is that the shower environment is a very humid environment, and some of this moisture will always enter the nail recess through your wall tiles, tile flooring, and often through your tiled bathroom niche. Read more: How to turn into a fairy How much steam will move into the rivet wall depends entirely on whether or not a waterproof membrane is installed on the shower wall and how resistant it is to ingress humidity of your shower corner. niche will vary greatly, depending on the type of niche you decide to build/install, and of course the waterproofing strategy.

Risk value?

With this moisture penetration problem, you can see why installing your shower recess to an exterior wall is risky. The space is filled with insulation. Even a small temperature difference can cause moisture in this shower enclosure to condense on the inside of the wall. waterproof membrane on the shower wall. With a corner shower taking up most of the space in the 3 1/2″ stud recess, moisture condensation in the recess is virtually guaranteed if the outside temperature drops a few degrees compared to the inside. if the bathroom walls and niches are properly waterproofed and there is enough space behind the shower niche for adequate insulation. In other words, you should definitely ask a trusted local contractor before you decide to build a shower niche into an exterior wall to avoid this potential shower niche installation mistake.

See Also  How To Access Discord Top Secret Control Panel

Bonus tip:

Do not install the wrong shower stand

This may not seem like a huge mistake when it comes to installing a bathroom area but as a bathroom remodeling contractor I hear a lot of people express regret about choosing the wrong shelving option for their bathroom. their tiled niche. if a custom niche) or 2 inch thick foam sheet (see below). This is often the most unfortunate shelf choice because it is difficult to clean (especially the corners) and the grout lines are yellowed and moldy. glass shelves. A bit more expensive for the material but it is usually a “luxury” shelf alternative for most tiled shower niches. These shelves are very popular because they are sophisticated, look modern and are considered attractive by most. However, many people complain that glass shelves are difficult to keep clean and soap falls off too easily. The opinion is that the shelf is suitable for a stainless steel shower. In fact, I thought that was awesome so I decided to design one to meet my client’s needs.

Pack (again)

Installing a shower niche can be a complicated and risky endeavor, but these 5 mistakes when installing a large shower niche can be avoided. Posts about New Shower Rack Options.Good luck with your new shower remodeling project AND enjoy your new shower niche! Please leave a comment below if you have any specific questions about shower installation. I’d be happy to help! This post is for informational purposes only and should NOT be construed as professional advice. You should always consult a licensed local contractor before undertaking any remodeling work in your home. Click here to see my full Personal / Professional Disclosure.Read more: Simon Air Rules | Top Q&A

Last, Wallx.net sent you details about the topic “5 BIG Shower Niche Install Mistakes To Avoid In Your Shower Remodel❤️️”.Hope with useful information that the article “5 BIG Shower Niche Install Mistakes To Avoid In Your Shower Remodel” It will help readers to be more interested in “5 BIG Shower Niche Install Mistakes To Avoid In Your Shower Remodel [ ❤️️❤️️ ]”.

Posts “5 BIG Shower Niche Install Mistakes To Avoid In Your Shower Remodel” posted by on 2021-10-23 03:29:09. Thank you for reading the article at wallx.net

Rate this post
Back to top button