How To Make A Homemade Violin Bow
Would you like to make your own bow? Just read this guide and you will be able to! Read: How to make a homemade violin bowA bow is actually a rod of horsehair. So first we need horsehair. Hair color doesn’t matter, they’re basically the same, just one push I bought my hair from topqa.info. You can also buy a horsehair for under 10 euros. 
They sell 500 grams of black hair for 100 euros. To do it once, cut the amount of hair you want and tie them together with a large knot, then put some super glue on the knot.
Then you need a stick. Hardwoods are best, but most woods will work. Aged wood with a straight grain is best: +/- 75cm long and 12-15mm thick. For frogs any kind of wood is good. 
You need part of approx. 50X25X15 mm. The tools I recommend for making your own bows are:
Let’s start making frogs. Bring the piece down to 45 x 20 x 13 mm. You don’t have to be too precise, but try to make it square in all directions. A violin frog should be 10 to 11 mm wide, a cello frog should be about 12 mm, and a bass should be about 15 mm wide.
Next is to make the frog lower on its back side, then you can round it, it’s important that the frog’s highest point in the front is on the side of the square. Create a bed for the hair on the round face. I make the cuts first with a saw and then deepen it with a file. The width (9mm violin & viola, 10mm cello, 12mm bass) of the bed is the width of a strand of hair that you will get. 2mm depth.Read more: how to download gyazo pro for free
Cut your rod at 70 cm for a violin or violin bow, about 65 cm for a cello or bass bow.
Drill a hole in the middle (diameter: 4mm violin, 5mm cello, 6mm bass), 3cm from the tip of the stick. Try to make the whole thing at a right angle to the stick. If your hole is not exactly centered, you should be able to adjust this after you shrink the bow.
Drill a second 4mm hole (5mm cello and 6mm bass) on the other side, 1cm from the end of the string. That will be the tip of the bow. Take your saw and make a cut (2mm wide) from tip to hole. If it’s not wide enough, make 2 cuts side by side, or use a knife or thin file (nail) to widen the cut. a better balance. For the violin bow, I recommend 10mm tall and 12mm wide at the frog end and 6mm high and 8mm wide at the tip (cello range is 2mm, bass is over 4mm). It’s wider and taller so the tip doesn’t become too flimsy and for added lateral stability. I used a flat surface, but if you don’t have one, you can use a file or scraper to reduce stickiness. The faucet should be even and straight. Try to keep the holes in the center of the stick, you can create an octagonal steam or do this later, after the hair is in place.
To prevent the frog from slipping, cut on the rod about 50mm from the first hole (wider side). The cut should be about 2mm deep, not more than that, or you’ll weaken the rod more than it should. wood away from the hole and the cut. It must be divided in depth: full height at the hole and 2mm deep at the cut. Hold flat so that the frog sits firmly on it. Now we come to the hardest part: feathering.
Try to get the same amount of hair as you would on a normal bow. A violin bow requires a minimum of about 120 hairs (4 to 5 grams). A bass bow has twice the amount of hair and a cello in the middle. First, tie the whole bundle together with a strong thread. Knot and wrap the yarn around your hair until it’s thick enough that it can’t slip through. 4mm hole in your rod. Tie the top back and trim the thread, trim off the excess hair and put enough glue at the ends and over the knot so that the hair becomes rock hard, to easily thread the hair through the hole. Wrap the head loosely with tape. Push the nozzle through the hole in the frog’s face from above and pull it through. Attention: Make sure you thread your hair from the right so that the hair rests on top of the frog. Read more: How to make the club car faster Now you remove the tape. Hold the stick firmly on the table or have someone hold it down for you.
Wet your hair to make it easier to comb.
Start brushing at the ends of the curls. You want all hairs to have the same tension, not cross each other. The comb helps to put them side by side, the pressure of the fingers gives them equal horizontal tension. Go through the hair about 10 times with the comb in hand, pressing two fingers together, until the strands look flat and even. After the hair is nice and even, tie a knot at the end, about 1cm longer than the length of the stick. Pull the thread around the hair until the knot is thick enough that it can’t slip through the 4mm (5mm cello) hole in your stick. Knot the end and trim the thread, trim off the excess hair and put some super glue on the end of the hair. Now put the frog in. If the hair ribbon looks twisted, you can still twist the knot until your hair looks even.
Hair is obviously too loose. To tighten it. First remove the frog. Then pull out about the knot. 1 cm at the top and knot the second big enough not to slip through the hole. Place Superglue on the button as you did the first time. Put the frog in position and see if there’s enough tension now. To do this, it is better to curl the rod so that the hair is released, the hair must be short enough for the curling rod to work. Now, you apply some turpentine to your hair and brush it for the first time. If the fur is not tight enough, take the frog out and tie a new knot a little shorter and then tie the knot where. If the fur is too short, you can remove the wood from the frog, just make the furrow lower and the feathers less tight.
The bow may still be too stiff and you want it to be more flexible. Softer bows usually have a nicer sound, but if they are too soft, they will become slow and unstable. So be careful about how much wood you remove. Continue to test the bow. A gamut or two can make a huge difference in playability and sound. The stick can have 8 sides like mine, but you can also make it round, oval, or triangular. There are no rules or measurements to follow, just trust your intuition, you are good and this bow is for you. The bow violin is good at about 60 grams, violin at 70 grams, cello at 80 and bass over 100 grams. If the bowstring is tight, the bend of the rod should be even, If you see a spot where the rod doesn’t have any curves, that’s where you have to remove some wood. Just do it! Read more: How to stream hbo max when discord
Last, Wallx.net sent you details about the topic “How To Make A Homemade Violin Bow❤️️”.Hope with useful information that the article “How To Make A Homemade Violin Bow” It will help readers to be more interested in “How To Make A Homemade Violin Bow [ ❤️️❤️️ ]”.
Posts “How To Make A Homemade Violin Bow” posted by on 2021-11-01 23:25:14. Thank you for reading the article at wallx.net
