How To Make A Wooden Surfboard
Happy May! Summer is just around the corner and we’ve spent the weekends (and some weeknights) at the beach house, racing to get ready and running ahead of Memorial Day. Even with our limited time, I saw an opportunity for a DIY project and couldn’t help myself… In the children’s bedroom downstairs, there is an empty wall between the bed and the door. into the solarium. I love the idea of decorating a surfboard in a beach house and this spot is the perfect size to hang on the wall.
My online search resulted in a small selection of used real surfboards that didn’t look the way I wanted or custom wooden surfboards that didn’t fit the budget. There is only one solution: Do it yourself ???????? If you follow me on Instagram, you may have come across my stories documenting the process! To get the width I wanted (1-2 feet), my first thought was to attach two 10′ panels together via a Kreg jig, but then I found the $ Pine Wood Panel This 30 20″ x6′ is the perfect size and doesn’t require any prep work (baby and vacuum are not included):
This is the only material needed for this project (assuming you already have paint/stain/tools) and will take less than an afternoon (unless you have young kids—it could take two days ????) Before I started, I searched online for inspiration and found a surfboard design/shape to make my model afterwards. I find it much easier to refer to something than to try to create it as you go on.
Step 1: Mark your center line
Contents
Measure and mark the center of your board at both ends (sorry for the blurry photos, most of this is a screenshot of a video I took as I don’t plan on writing a blog tutorial until then! )
I also went ahead and drew two lines (equidistant from the center) to use as guides for the tape, which would later become stripes. I didn’t make them dark enough, and by the time I was ready to tape, I had to redo them—so either make them dark or you can skip this step and add them later.
Step 2: Trace your board outline
Cut a strip of wrapping paper and glue it to one half of the board. Then, using a pencil, outline the outline of one side of the board. Yes, a bit of artistic skill is required here, but you only need to draw half of the board and it’s not too difficult if you have a reference photo to copy.
Once you’re happy with the shape of your contour, cut it out with a hand razor.
Now you can trace your shape on the board.
Once one side is done, flip your paper over to the other side and make sure the center points are aligned so the board will be symmetrical. Then follow up again while holding your baby with the other hand as he tries to tear your paper. Read more: how to make a water tank with pvc pipes
And the hardest part is over!
Step 3: Cut your table shape
Using a jigsaw, cut along your contour. I’ve had this Black & Decker jigsaw for years and it’s one of the best DIY tools for beginners. You will want to do everything when you start using it!
I rushed through this step trying to get it done before my nap time ran out, but it doesn’t have to be perfect. The sanding step will smooth out many irregularities.
It is also very easy to go back to the jigsaw and fine-tune the areas that need to be manipulated.
Step 4: Sand the edges
I started with my mouse sander because my orbital grinder is at another house. It helps smooth the edges but it takes forever and doesn’t make a huge difference.
I did as much as I could with the Mouse, but it still needs more than that.
I finally found our orbital grinder, and the difference is night and day! You can see in the photo below how the orbital grinder (with 80 grit paper) actually shapes the board and rounded the edges, compared to the Mouse.
Immediately, the sanding was done.
Step 5: Clean the wood stain
This step is optional, but I think it will look more complete. My plan is to paint the board but expose the wood for the stripes. I used Minwax Special Walnut which is a nice neutral tone.
The stain is applied to the area where the stripes will appear (no need to stain the whole board!) I use a light coat of paint and let it dry for just 20-30 minutes before moving on to the next step.
Step 6: Create your stripes
Depending on the design of your table, this section is also optional. After tinting, I couldn’t make the original pencil lines I drew for the stripes, so I decided to redraw them using 1 × 2 glued down the center as my guide . microwave oven
I find this method much faster/easier than drawing them in the first place, so if I had to do it all over again, this is what I would do! When 1×2 is tracked on both sides, simply tape along the lines. I used 2 inch paint tape but you can use whatever you want!
Step 7: Paint
Now we’re getting to the fun part! Choose a color and paint your board. I rummaged through our garage for paint samples and landed at SW Falkland Blue. I brushed it to save time/clean up, but you can also use a roller.
Then comes the most fun/nervous part… remove the ice! Luckily, this tape worked like a champ and my lines were nice and sharp.
Step 8: Attach the hooks
Once the paint dries, flip your board over to the back. I wanted my board to hang a bit off the wall instead of leaning directly against it, so I cut a few pieces of wood chips to use as spacers and screwed them on to the back.
Then I used two picture hooks and attached them to my top spacer (this photo shows the board upside down):
Step 9: Seal
To protect the finish, you don’t want to skip this step! I used Minwax Polycrylic in a semi-gloss finish (any clear polish or poly will work well).
A few coats is all you need (or more if you want to use it as a toy)…
Step 10: Hang on the wall
We have made it to the last step! Measure and mark where you want the board to hang, then insert the drywall anchors (we like the self-drilling type) into the wall. Slide your hook through the screws and voila!
A few of you told me that the board seemed better to hang another way so we could flip it over. What do you think?
This is a fun little project, and it adds the perfect relaxed surf feel to this kid’s bedroom (and for only $30!) I think it would make a great addition to any space. Which has a coastal/beach theme (without searching/over-the-top). The best part is that you can completely customize the size, shape, color and design to suit your style. If you’re planning on making one, be sure to check out this project’s step-by-step video/timelapse on Instagram. We tried doing another DIY project for the beach house last weekend and I’m working on another tutorial for that next. I’ll post it here tomorrow for you guys, so don’t go anywhere!
Read more: Small decorating ideas with big impact: off-centre wall decor
Last, Wallx.net sent you details about the topic “How To Make A Wooden Surfboard❤️️”.Hope with useful information that the article “How To Make A Wooden Surfboard” It will help readers to be more interested in “How To Make A Wooden Surfboard [ ❤️️❤️️ ]”.
Posts “How To Make A Wooden Surfboard” posted by on 2021-10-26 06:31:09. Thank you for reading the article at wallx.net
