How To Set Up Fishing Pole For Bass

TYPES OF FISHING BASS

Contents

The following list of bass fishing rig layouts is not an exhaustive list. Read the tips below to ensure that your bass rod setup uses the correct bass rig and button for best results. There are bass rigs for the lake and bass rigs for saltwater. Learn about the different types of fishing rigs before your next fishing adventure.

1. CAROLINA RIGS

Carolina Rigs are Sliding Sinker Rigs specially created for bass fishing rigs with a grass free hook and a soft plastic worm. A Carolina rig works with egg sinks up to 3 or 4 ounces. Lighter recessed bars help the truss pass through grass or grass. Read: how to set up a bass rod For heavier weights, replace the set with a fish machine slide (a hollow tube with an attachment point for heavier sets) and clip onto a heavier one quantity. To keep the sink or reel from getting caught in the swivel, place a small bead on the center line between the sink and the reel. The advantage of using this bass rig setup is that it allows the fish to grab the bait without detecting the weight of the sinker. Fishing Rig: How to Make a Carolina Rig

To make a soft plastic worm act as a weed-free lure, you’ll want to start with a compensating foot worm hook (though other types of hooks will also work).

To start, press the hook end into the center of the worm’s head so that the sharp tip penetrates only a quarter of an inch or so deep, then push the sharp end over the edge of the worm. Slide the hook over the head of the worm to the offset, twisting the hook 180 degrees so it points back towards the worm.

Hold the worm by the head and let it hang straight down the hook. Take the worm between two fingers where the hook tip rests against the worm’s body. Just lift the worm slightly and tilt it so you can fully push the hook tip through the worm’s body.

Pinch the worm at the hook point and thread it into the spot just below the worm’s skin to make it free of weeds.

You may have to squeeze the worm at the top of the hook to make the whole thing lie flat. If the worm is raised or bent, try again. The body of the worm should lie in a straight line for it to work.

2. TEXAS RIG

The Texas Rig is one of the most popular bass fishing rigs. It’s a way to fish a soft plastic worm near or in mulch like weeds. This truss requires a special conical weight and a “deep hook” designed to thread through so that the point of the hook is not exposed. This allows these rigs to work through weeds or thick mulch without jamming. Fishing Rig: How to Tie a Texas Rig

Slide a cone weight over your main lane with the bottom of the cone facing the end of the lane

Tied to a deep hook free of weeds.

Add a soft plastic worm to hook through the worm’s nose. Push the hook end in ¼ inch and then poke it out of the face of the worm at a 90-degree angle. Run the entire hook to the outside until you get to the eyelet.

Once you’ve reached the eyelet, rotate the hook so that the point is facing the worm’s body.

Next, place the hook on the side of the worm to keep the worm straight. Trace where the bend of the hook intersects the deep bottom. That’s where you want to insert the hook point and then thread it into the worm’s body.

Some anglers like to clamp the weight in place with a small toothpick.

3. DROP SHOT RIG

Drop rigs are also popular bass fishing rigs because they allow you to put a soft plastic bait over the bottom so that the bass is hung right on the bottom. But they are also excellent rigs for catfish and many other species. It consists of a weight and a hook tied in such a way that it is suspended with the hilt parallel to the bottom. The palomar button is a great way to go with this woofer setup. The hook should be facing up to prevent it from getting stuck. Fishing rigs: How to tie a fishing rig

Double your line and pass it over the eye of the hook. Make sure to leave enough tag tails to tie your weight down for later. Tie a knot overhand but do not pull tight, leaving the hook free to hang.

Pull the loop from your top knot over the hook and tighten by pulling both sections of the rope. (You’ve basically tied a Palomar knot on your hook).

Take your card line and run it through your hook eye again. The goal is to make the hook protrude at a 90-degree angle from the main line so that the shank of the hook is parallel to the bottom face.

Then tie your weight to your end-of-line tag.

Add lures or plastic worms to your hook.

4. NED RIG

Read more: How to Make Salsa at the Border The Ned Rig House may be one of the best fishing rigs to use during the fall and winter months when the big mouth is lethargic. Smaller baits will be a better producer in these conditions because sea bass simply don’t want to chase large prey with a lot of movement. soft plastic bait and jig head. All you have to do is follow three easy steps to learn how to install a bass fishing rig that you can use in harsh conditions. Fishing rig: How to set up a fishing rig for Bass The Ned Rig

Take a 3-inch long soft plastic bait and attach the hook of the 1/16-ounce mushroom head (made in 1 or 2 hook sizes) to the tip of the bait.

Push the hook about 1 inch down through the center of the lure and to the outside of the lure so the hooks remain in contact.

Attach the Ned Rig to 6 feet with 8-pound fluorocarbon leadership and then attach to it your main line using a line-to-line connection, such as a Uni-to-Uni button.