Where is 7/8 on a tape measure

A tape measure, commonly known as a tape measure, is a piece of metal tape with even divisions used for measuring. The tape is usually yellow and is rolled in a plastic box. Tape measures are commonly used in construction, structure, construction, house works, crafts and woodworking. They are typically available in lengths from 6 ft to 35 ft. Read: 7/8 position on tape measure Tape rulers can have metric and metric, metric, or metric only measurements.

Easy methods for learning a sole measurement

Contents

On a British tape measure, the lines represent lengths in inches and fractions of inches. Each large tick represents one inch (1 ″), and the middle tick represents the following fractions: 1⁄16″, 1⁄8″, 3⁄16″, 1⁄4″, 5⁄16 “, 3⁄8”, 7⁄16″, 1⁄2″, 9⁄16″, 5⁄8″, 11⁄16″, 3⁄4″, 13⁄16″, 7⁄8″, and 15⁄ 16″. To read a tape measure, find the number next to the large tick, then find how many small ticks cross that measure. Add the number next to the large tick with the fraction to get the measure. Example : if your five ticks exceed the 4 tick, then the measure is 4 5⁄16″. Reading a tape measure is like reading a ruler.

What do all the points mean?

Fractions of inches for each mark

See decimal equivalents for all fractions on the tape measure. You may also like our fractional inch calculator to convert between decimal and inch fractions and get decimal equivalents.

Equivalent to fractions of inches, decimals and millimeters

Graph showing fractional, decimal, and millimeter-equivalent measurements Decimal Parts Millimeters 1⁄16” 0.0625 1.5875 1⁄8” 0.125 3.175 3⁄16” 0.1875 4.7625 1⁄4” 0.25 6.35 5⁄16” 0.3125 7,9375 3⁄8” 0.375 9,525 7 16” 0.4375 11,1125 1⁄2” 0.5 12.7 9⁄16” 0.5625 14 ,2875 5⁄8” 0.625 15,875 11⁄16” 0.6875 17.4625 3⁄4” 0.75 19.05 13⁄16” 0.8125 20.6375 7⁄8” 0.875 22.225 15⁄16”0, 9375 23.8125 1″ 1 25.4″

Easy methods to learn a metric measurement

The metric tape measure has symbols associated with royal fashion, however these are specific to centimeters and millimeters. Larger lines on a ruler are numbered in centimeters and smaller lines are in millimeters. 9mm mark between every centimeter on the tape. On a metric tape measure, there can be 1 cm between each large numbered mark and there can be 1 mm between each smaller unnumbered tick.

Easy methods to use tape measure

Basically, get the most out of your measuring tapes with follow-up suggestions for using them.

Easy methods to use ice buckles

Nearly all tape measure reels have a lock to maintain the tape measure from jerking. That is useful if you need to relieve stress on the tape measure or if it is necessary to put the tape measure down while it stretches. On this Stanley FatMax dummy, the slide lock is the big black button at the top. This slide down locks the tape open to prevent recoil. As an Amazon Affiliate, we may earn commissions on qualifying purchases from Amazon. Get extra teaching

Easy methods to use slide hooks

A prominent feature of the tape measure is the hook on the top of the tape measure. This serves a dual purpose to prevent the tape from entering the housing and to allow hooking to the ends of what is being measured. You may find that the hook tip just slips or bounces off a little. It is by design to account for the thickness of the hook, allowing the tape measure to be accurate when hooking into the floor and also when headbutting as much as the floor. Please note that tape measure must not have slide hooks as they will not be accurate.

Easy Methods to Use Stud Framing’s Suggestions

Read more: Where is the main payout rotated Most of the reels have purple markings at certain intervals: 16″, 32, 48, 64″, etc. These numbers are important in that they indicate center of directional for 16 inches on heart-shaped frame. Some gauges also feature 19.2-inch black diamond image intervals to the side. These diamonds are also used to refer to framing gaps for wider nail or stake spacing.

Easy methods to use nails

The hook on the tape measure usually has a small opening or groove in it. That’s actually used to allow the hook to hook onto a nail or screw, so it doesn’t slip when taking long measurements. That’s especially useful for longer measurements, like measuring across the entire size of a room or patio. On the hook above, the oval cutout is used to hook into a nail or screw.

Use the sides of the hook

Some tapes, especially profiling tape, have large hooks that can be used to clamp surfaces on the face of the hook. The use of these can improve the gripping skill of the hook and improve measurement accuracy because the tape measure does not twist to learn how to mark.

Easy methods for choosing the right tape measure

There are many measuring tapes on the market and many serve completely different functions. When choosing the one that works best for you, take into account what you’re going to use it for, how long you want it to be, and how much you want to spend it on. When choosing a tape measure, take into account the next options to find the tape measure that best suits you and your wishes.